Jump to content
SAU Community

Recommended Posts

Just remember to do it on a freeway lol, don't want anyone being arrested.

I was just gonna squirt it down the same road lol but Its better on the freeway because the road is smoother. 6krpm in 3rd gear is close to 140km/h. The car feels pretty dead coming from 1500rpm in 2nd, should be interesting to see how it goes from 3rd at 2k.

Yeah from 4900.

Dude.. It should be ON just after idle and OFF somewhere around 5... Turning it on at 5 would make your spool SUCK and your power rubbish. Please clarify the above?

& LOL @ the sarge in his army prints.

I just has a look in FC Edit and it only has VCT: then a value. For me it's 4700. Guessing it must be the switch off point as I can definitely hear my VCT solenoid click at just above idle when I give i give it a quick free rev. Can double check in sensor check later

Just for informations sake, specs on the corona.

1jz-gte

Hypergear TR44 turbo

Trust exhaust manifold

Trust 50mm wastegate

3" mandrel bent exhaust

500X300X76mm intercooler

3" intercooler piping

GFB Mach 1 BOV

2 front mounted gearbox oil coolers

Microtech LT12s and X6 igniter

X2 Excel radiator

No power steering or Air conditioning pumps

Techedge 2EO wideband o2 sensor

NOS kit (50 hp jets)

Greddy Profec B II

so it needs nos to get to 10.7? if so then what a useless post.

It did 11.8 without Nos. from that car's dyno reading:

tr441jz315kw.jpg

The Nos added about 35kws. Those are old school turbos. The Fnt G3 he should be getting the same power curve without Nos.

Is this car still racing today?

It did 11.8 without Nos. from that car's dyno reading:

tr441jz315kw.jpg

The Nos added about 35kws. Those are old school turbos. The Fnt G3 he should be getting the same power curve without Nos.

Is this car still racing today?

Full boost at 2400 on a 2.5L, is that thanks to the stall converter?

Full boost at 2400 on a 2.5L, is that thanks to the stall converter?

My brother spools a 3037 .63 nearly at idle on a POS 2.6 Sigma. All thanks to a 2200rpm stall converter.

It ends up making all of 170kw at 18psi with the exhaust housing glowing white but it gives the illusion of a very different turbo.

Ahh the stall converter, applying load to the engine at idle to create some boost.

Here is a run from about 2500rpm to 6000rpm in 3rd gear on low boost(around 14psi). I know the dash isn't visible enough but this isn't something I want to try and do more than once on the road lol. My car seems to always ping now at high boost so I think the removal of the rubber hose has had an effect on the tune...

Edited by SargeRX8

You can find FNT feed back from Random in page 87. Check index on page 1.

Any way. lots of talk about twin scroll turbine housings. At this stage I'm not convinced that they has a "major" affect but welling to do some tests.

So, we all know the air gap inside the turbine housing is the height of the inducer blade of the turbine wheel.

By placing a metal strip in between and half the gap is actually reducing the area of the gap enabling higher air velocity. To me this is another way of sacrificing top end power for down low response unless the size of the turbine wheel and housing is in a reasonably large size.

Theoretically I can archive this behavior by reducing the gap height at only 60~70% of the turbine wheel top without the divider in the center.

I've done a drawing converting single scrolled turbine housing into a twin scroll item, internal or dual gate bolt on to stock setup of course. Good thing is I can setup dual effective FNT nozzles inside that housing for even better response. I'll be doing a back to back tests using a G3 core. hopefully it’s worth the effort.

Any way, Do post up if you have any experiences or back to back tests with single to twin scroll turbine housings.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...