Jump to content
SAU Community

Recommended Posts

mm I think that was optional. he's user id is Abe2 send him an email. Or see if ScottyM35 have some thing invented.

Thanks Stao. :)

I do an 80mm alloy intake kit to suit the stock airbox with bov and breather fittings.

post-63525-0-13924300-1339087856_thumb.jpg

That 80mm one would it suit a atr43g3 ???? I want something that would allow standard air box connection with plumb back for both retic and oil breather

Get scotty to make one for you then.

It would suit the 80mm

Its been made 4inches for a reason. Best to have a 4inch intake pipe.

Also I've got a R33 turbo sent in for high flowing about week ago, job is complete, but it has no name or return address on it. Please pm through if that belongs to you.

Ok than can anyone make one up four inch and reduce to 3 inch ( Scotty ). It has to be three for the afm

I'm sure Scotty could do the same design in 4", PM him to discuss it.

Like you said, you are running an afm like a z32 in the standard position, so your intake will have to be 80mm at some point to be able to connect the afm.

Just get a 4" to 3" silicone reducer for one end of the intake.

Edited by Mitcho_7

Its been made 4inches for a reason. Best to have a 4inch intake pipe.

Also I've got a R33 turbo sent in for high flowing about week ago, job is complete, but it has no name or return address on it. Please pm through if that belongs to you.

It's been made 4 inches because of the anti surge ports, not because it needs a 4 inch intake. While 4 inch would be good there is no point if you still run the afm. Mine has run 350kw on a 70mm internal pipe so this one with a 3 inch internal should be no problem for most customers.

I can make any piping you need but I would need the car here obviously.

Do the g2.5/g3 have 4" intakes? I always thought they were 3"?

G2 is 3 inch I can't say about g2.5 but g3 is definitely a 4 inch intake that's why it needs the spacer on the manifold

That 80mm one would it suit a atr43g3 ???? I want something that would allow standard air box connection with plumb back for both retic and oil breather

Anyone ever tried putting a pod in stock air box with the arse cut out?

Whats the point?

Just chuck a high flow filter on there and enjoy.

Or do you want induction noises ?

With Hi flow panel filter and a metal intake pipe I get a sweet induction noise, you don't need a pod for it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...