Jump to content
SAU Community

Recommended Posts

mm I think that was optional. he's user id is Abe2 send him an email. Or see if ScottyM35 have some thing invented.

Thanks Stao. :)

I do an 80mm alloy intake kit to suit the stock airbox with bov and breather fittings.

post-63525-0-13924300-1339087856_thumb.jpg

That 80mm one would it suit a atr43g3 ???? I want something that would allow standard air box connection with plumb back for both retic and oil breather

Get scotty to make one for you then.

It would suit the 80mm

Its been made 4inches for a reason. Best to have a 4inch intake pipe.

Also I've got a R33 turbo sent in for high flowing about week ago, job is complete, but it has no name or return address on it. Please pm through if that belongs to you.

Ok than can anyone make one up four inch and reduce to 3 inch ( Scotty ). It has to be three for the afm

I'm sure Scotty could do the same design in 4", PM him to discuss it.

Like you said, you are running an afm like a z32 in the standard position, so your intake will have to be 80mm at some point to be able to connect the afm.

Just get a 4" to 3" silicone reducer for one end of the intake.

Edited by Mitcho_7

Its been made 4inches for a reason. Best to have a 4inch intake pipe.

Also I've got a R33 turbo sent in for high flowing about week ago, job is complete, but it has no name or return address on it. Please pm through if that belongs to you.

It's been made 4 inches because of the anti surge ports, not because it needs a 4 inch intake. While 4 inch would be good there is no point if you still run the afm. Mine has run 350kw on a 70mm internal pipe so this one with a 3 inch internal should be no problem for most customers.

I can make any piping you need but I would need the car here obviously.

Do the g2.5/g3 have 4" intakes? I always thought they were 3"?

G2 is 3 inch I can't say about g2.5 but g3 is definitely a 4 inch intake that's why it needs the spacer on the manifold

That 80mm one would it suit a atr43g3 ???? I want something that would allow standard air box connection with plumb back for both retic and oil breather

Anyone ever tried putting a pod in stock air box with the arse cut out?

Whats the point?

Just chuck a high flow filter on there and enjoy.

Or do you want induction noises ?

With Hi flow panel filter and a metal intake pipe I get a sweet induction noise, you don't need a pod for it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
×
×
  • Create New...