Jump to content
SAU Community

Recommended Posts

My turbo turned up while I was away at work, didn't even know it was on the way :P

Thanks Stao for all the help you've given me through this process, turbo looks good and can't wait to see how it goes. Now just have to finish my engine

20121120_201246.jpg

I only have the standard highflow which is good for 430hp.

270x1.34= 361rwhp

361*1.2=434 engine hp allowing 20% drive train loss (which is a widely accepted rough estimate)

Yours sounds about right,

My turbo turned up while I was away at work, didn't even know it was on the way :P

Thanks Stao for all the help you've given me through this process, turbo looks good and can't wait to see how it goes. Now just have to finish my engine

20121120_201246.jpg

Is that v-band???

V-band rear? yes

3.5" V-band

I will take some more photos in a minute, that was just a quick camera phone photo last night when I got home from work

Very nice looking turbo, Not sure if I want to paint the housing or not lol

No im just wondering,

anyways i got it retuned this morning again and because of timing and it was sort of pinging my tuner had to back the power off, now its on 255kw on 18 psi, i'll post the final tune tonite when i got a chance, im happy with the turbo either way.

V-band rear? yes

3.5" V-band

I will take some more photos in a minute, that was just a quick camera phone photo last night when I got home from work

Very nice looking turbo, Not sure if I want to paint the housing or not lol

Very nice. I need one of these V-Band rears :woot:

That was my ceramic roller bearing highflow with a .60 comp housing :yes: and new externlly gated through turbine housing.

its pretty interesting seeing the 6boost's manifold has very long runners. any one can share some theory in doing that?

Equal length runners and merge collected so exhaust gas gets to the Turbo in equal/even bursts isn't it?

Pretty keen for this engine, really hope I can get the ext gate to work but think life won't be so bad if I have to go int gate I don't think

Need to trim the Turbo studs as one of them is fouling but other then that I'm very happy with how its looking :)

V-band rear? yes

3.5" V-band

I will take some more photos in a minute, that was just a quick camera phone photo last night when I got home from work

Very nice looking turbo, Not sure if I want to paint the housing or not lol

Prob just me or the photo but v band doesn't look 3.5".

Plus I thought Stao told me once he could only do 3" max.

Hi Stao,

Long time no speak! As you already know, I'm currently running a top-mount Garrett GTX3076R but looking to return the car to stock-ish to sell and was wondering what the boost response is for the hi-flowed R33 standard turbo and the hi-flowed R34 turbo like compared to the stock R33 turbo.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I personally would go with cutting out the rubber. Then deal with getting sleeve off separately. Rubber can be painful to cut, it loves to jam up cutting tools. I normally have success with drill bits, deburr bits, angle grinders, jigsaw, reciprocating saw, and never forget... fire. Obviously different tools won't work in all locations you're trying to work with, and you need to be comfortable with each. You personally may be happy slowly slicing it out with a razor blade, if you are, go for it with one too! Feel free to wait for others to weigh in also on their thoughts.
    • So ... I got everything disconnected and started dropping the frame. Three of the four mounts started to come down but the fourth one (the one with the nut that gave me all the trouble) won't budge. The inner metal sleeve stays up tight against the chassis rail although the outer part of the mount drops a bit (and can be levered quite a lot more) but it's just stretching the rubber bushing. So I reckon there's some serious corrosion inside the inner sleeve and holding it tight to the lug at the top of the bolt. Tried everything I can think of so far: penetrating oil, whacking the top of the sleeve to vibrate it and wedge a screwdriver blade in there. I also tried to turn the inner sleeve a bit by hitting it with a chisel at the bottom. It's stuck solid. What do you think about cutting the rubber with a blade so I can drop the subframe around it anyway. Then worry about getting the inner sleeve off after? Will that work? Is it gonna give me even more problems?
    • Steam valve seals are usually responsible for cold start smoke, it goes away once engine warmed up. Disconnect it let engine breathers and let it breath freely, see if problem goes away after a short drive. Also check to make sure engine oil drain pipe is not blocked or kinked. 
    • Haha thanks! Yea I'm moving over from 2x 1000cc jets pre throttle over to 6x 190cc direct port jets and 1x 500cc pre throttle jet.  Direct port comes with all the advantages you would expect, except that pre throttle does cool down IAT'S more. That's why my direct port nozzle placement is closest to the plenum as possible in the runners to allow the air more time to cool before being sucked in. I'm also putting that one 500cc pre throttle jet to help with more cooling. It's a hybrid system. There's a lot more advantages to moving over to a PWM solenoid with a constant pressure system vs my old PWM pump setup, but I'll get more into that once I'm done converting everything over. The ricer in me is excited to see SS tubing all over my manifold though!
    • Very cool, see what I did there? 🥲 Wild WMI setup, first I've seen where it's on each cylinder runner, usually I see a single jet pre throttle.
×
×
  • Create New...