Jump to content
SAU Community

Recommended Posts

Stao tried to seach and find the answer because I think you have told me before.

But what do you think the limit of the SS1PU would be on water meth injection.

Mine was limited due to the heat.

So in the future once I save the dollars I will be going that route.

But at the same time dont want to find it hits a wall at like 260rwkw

The R33 highflowed turbos would support up to 240rwkws while R34 turbochargers can be high flowed to support 260rwkws. response wise high flowed R33 turbo is about 300RPMs earlier. Personaly I prefer to run a highflowed R34 turbo

Actual water meth (50/50ish mix) will get you results similar to E85 if implemented right.

Yet to see any E85 results on the ss1pu

If you know of any then I would love to see.

Just want to know what to expect if I do it

Prob just me or the photo but v band doesn't look 3.5".

Plus I thought Stao told me once he could only do 3" max.

I thought it was 3.5" cause we were talking about a 3.5" dump. But if its 3" im not worried, makes it easier to get the dump to fit to the turbo anyway

Yet to see any E85 results on the ss1pu

If you know of any then I would love to see.

Just want to know what to expect if I do it

Based on the spec of the thing it will lay close to 300.

I'll give you a good deal on my WMI kit if you want to be the first to try. Not trying to be a viral sales kent.

Based on the spec of the thing it will lay close to 300.

I'll give you a good deal on my WMI kit if you want to be the first to try. Not trying to be a viral sales kent.

Pm me prices and details of the kit

Don't know to much about them but would need one with a good fail safe

Yet to see any E85 results on the ss1pu

If you know of any then I would love to see.

Just want to know what to expect if I do it

I fitted one to an M35 in the stock housings that managed 300, not a good indication of what it would do on an RB but it should be close.

I fitted one to an M35 in the stock housings that managed 300, not a good indication of what it would do on an RB but it should be close.

Good to know Stao has done a nice job with the turbine side of things. I can't wait to have mine running :)

How did it go on the VQ?

I fitted one to an M35 in the stock housings that managed 300, not a good indication of what it would do on an RB but it should be close.

Still means it can flow that sort of power

Spoke to my clutch guy today and his going to get back to me if it can handle that power.

If it can't then I can't afford it

If it can then I will be doing that over Christmas

When in for a return tune today.

After a few runs the manifold pretty much overheated and split one of the silicon hoses so had to call it a wrap again.....

We got up to 283 rwkw before the silicon hose split

Tune as it stands atm:

74702_555188291162201_22398245_n.jpg

I might try out one of staos dual actuators as its at 19.5 psi dropping to about 15.5 psi i think

What turbo is that Tony? Is it stock intake mani?

Cheers

Justin

Hey Justin its an internal gate ss2 turbo on 98octane

I got a one of staos china manifolds

It moved nearly 2 ton down the quarter in 12.9, faster than mine as he gets boost on stall.

I think it hit 20psi by around 3k...

Thats very nice! Theres always a point where you can have a faster car with a lower number, which is something im scared i may have overshot by going the SS1PU on my SR but we will see!

Good to note that the unit is an all round good turbo though. Everyone who has one seems to be happy with it regardless of how much power they made (its only numbers anyway). Props to Stao yet again!

When in for a return tune today.

After a few runs the manifold pretty much overheated and split one of the silicon hoses so had to call it a wrap again.....

We got up to 283 rwkw before the silicon hose split

What fuel Tony? Its starting to shape up nicely (ignore the fuel question coz you replied yourself before I hit send)

The R33 highflowed turbos would support up to 240rwkws while R34 turbochargers can be high flowed to support 260rwkws. response wise high flowed R33 turbo is about 300RPMs earlier. Personaly I prefer to run a highflowed R34 turbo

21U @ 260rwkw on United E85. Only 14PSI as ter rear tyre can't handle more around the track.

This turbo has now done over 40 track days, including WTAC.

Responce..5th gear at 110 is pretty much on boost. Its over 100rwkw at 3000rpm on trents dyno.

Update on car.

Car is finally tuned:

R34GTT

Mods:

SS2 Internally gated Turbo

98 Octane

China manifold

3inch JJR dump & 3inch exhaust

ID 1000 injectors

Yellow jacket coil packs

Hybrid return flow intercooler

Scotty 3inch intake

483595_556895830991447_473150841_n.jpg

About 190rwkw at 4,000 rpm so happy with that!

About 20psi falling over to about 16psi i think

Note this is a conservative track tune

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...