Jump to content
SAU Community

Recommended Posts

..... isn't the manual rated lower than the auto too? Anyway, isn't the 6 speed auto much better suited to the car, even unladen?

I don't see the logic in towing with an underated tow vehicle, crash it and no insurance for anything, bye bye to both vehicles.

The clutches in them do not cope with towing, even with loads under the limit (mind you, the 1600kg limit is for a car with a 65kg driver and nothing else on board) stick with the auto's with the heavy duty tow pack and they are Ok.

I don't see the logic in towing with an underated tow vehicle, crash it and no insurance for anything, bye bye to both vehicles.

Bingo!!!

Also, something that most people don't know is that if you're towing more than 2000kg, then your trailer must be equipped with brakes on all 4 wheels, and must also have a break away system fitted (so that the trailer brakes automatically apply if the trailer becomes disconnected from the car). Very few car trailers have this unless it's specified as a 2500kg (or more) trailer. That's why you'll see the load rating on all car trailers as 2000kg TOTAL.

I haven't read the wording lately, but I believe that the 2000kg refers to the total trailer mass + the load on the trailer - the downforce on the tow ball (normally about 100kg or so). Note I haven't double checked for a while, so that last bit may not be correct. Best to determine for youself before committing.

The auto Falcons used to have a higher towing capacity than the manuals (in the days of the EL, anyway). Don't know if that's changed in recent times though.

Many modern 4WD's have piddly clutches that aren't really up to the task of regular towing. In the name of making the 4WD's more user friendly for their intended purpose (soccer moms, etc.) they have lightened a lot of the controls by fitting more car-sized components. My PAthfinder will quickly smoke the clutch while towing if I'm not careful, although after 75,000km it is still going strong.

Many modern 4WD's have piddly clutches that aren't really up to the task of regular towing. In the name of making the 4WD's more user friendly for their intended purpose (soccer moms, etc.) they have lightened a lot of the controls by fitting more car-sized components. My PAthfinder will quickly smoke the clutch while towing if I'm not careful, although after 75,000km it is still going strong.

they shoulda stuck with the power assisted clutch like my 88 GQ TD42 has instead!

What the hell is wrong with heavy clutches anyway? My wife hates these modern light clutches as much as I do. We both loved the heavy clutch in the GTS2 we owned many years ago (was a heavy sumbitch, but great feel - the clutch that is, not my wife :banana: ). all others since then have felt like shopping trolley clutches - very disappointing.

I've been towing my 1200kg car+trailer abit lately with my brand new Holden Ute SS-V and love it. I put the cruise control on the speed limit and it sits on it the whole way everywhere I go. When on a flat road it switches the v8 into 4 cylinder mode and I can do 6L/100km whilst towing.

I've been towing my 1200kg car+trailer abit lately with my brand new Holden Ute SS-V and love it. I put the cruise control on the speed limit and it sits on it the whole way everywhere I go. When on a flat road it switches the v8 into 4 cylinder mode and I can do 6L/100km whilst towing.

IRS :)

I've been towing my 1200kg car+trailer abit lately with my brand new Holden Ute SS-V and love it. I put the cruise control on the speed limit and it sits on it the whole way everywhere I go. When on a flat road it switches the v8 into 4 cylinder mode and I can do 6L/100km whilst towing.

Changed how many rear tyres Ben ?? The IRS on these is a JOKE. My mate had had 3 sets on the back in 50K

Only Commodore/ute that can really tow properly is the VZ Crewman crew cab which has a live rear axel and 2500kg towing capaity. Preferably with a V8.

I have a 6 cylinder one which is marginal/good for towing a car but is great otherwize.

Having said that. You will prob not have an issue cause you car/trailer is so light. The massive trailer and the zed on it where pushing 2000kg. It was a very long trip from QLD.

PICT3904.jpg

Edited by Tektrader69

yeah thanks for the comments. I really want a manual and i know that it's rated at less but I'll be getting an aftermarket heavy duty (2000kg) tow bar. will prob wear out the clutch. I only tow every couple of months so hopefully it will be ok. Gotta be better than my VS SS.

I've just read on the ford forums that they flog out tailshaft uni's. Might need to beef up the suspension so it's not dragging on the ground.

I really don't want an old 4WD. They may have the weight to make it legal to tow with but they're slugs. and uncomfortable.

Also, something that most people don't know is that if you're towing more than 2000kg, then your trailer must be equipped with brakes on all 4 wheels, and must also have a break away system fitted (so that the trailer brakes automatically apply if the trailer becomes disconnected from the car). Very few car trailers have this unless it's specified as a 2500kg (or more) trailer. That's why you'll see the load rating on all car trailers as 2000kg TOTAL.

I haven't read the wording lately, but I believe that the 2000kg refers to the total trailer mass + the load on the trailer - the downforce on the tow ball (normally about 100kg or so). Note I haven't double checked for a while, so that last bit may not be correct. Best to determine for youself before committing.

Well my trailer weighs 700 and I'll say my gtst is about 1300 :cool: so I just scrape in under 2000kg.

so you plan to exceed your towing capacity by at least 25%. good idea, what could possibly go wrong?

and your biggest concerns are clutch and unis? legality, safety and insurance don't even rate a mention.

I wish cops actually targetted real safety issues like these rather than putting speed cameras on highway on-ramps...

Well my trailer weighs 700 and I'll say my gtst is about 1300 :cool: so I just scrape in under 2000kg.

Sure you can put a two tonne rated towbar on it, but it doesn't mean it will be legal. If the manufacturer states 1600kg, then 1600kg it is.......

(as an aside does anyone know if the legalities of towing still vary massively from state to state? I remember many years ago it was always a drama when towing our 7 metre Sharkcat into NSW because the rules changed dramatically)

so you plan to exceed your towing capacity by at least 25%. good idea, what could possibly go wrong?

and your biggest concerns are clutch and unis? legality, safety and insurance don't even rate a mention.

I wish cops actually targetted real safety issues like these rather than putting speed cameras on highway on-ramps...

Well I've towed the same setup on a 1200kg tow bar coz I didn't have anything else.

Sure you can put a two tonne rated towbar on it, but it doesn't mean it will be legal. If the manufacturer states 1600kg, then 1600kg it is.......

I know it won't be legal but I'll pay the fine. I think it would be over engineered and 1600 is conservative. Manufacturers would have to be on the conservative side.

Back on topic, a F150 LWB with 351 on LPG makes a great tow vehicle.

Yeah but would be a pigg to drive around.

I've towed far in excess of legal and manufacturer's limits too, the point I am trying to make is now I'm older and smarter I certainly wouldn't be risking (for arguments sake) a 40k tow car, a 30k race car, and a 4k trailer being totally uninsured if I was to have a major accident, keeping in mind if you run into another car and hurt someone, no insurance there either.

Changed how many rear tyres Ben ?? The IRS on these is a JOKE. My mate had had 3 sets on the back in 50K

Bought it new and only put 3500km on it so far in 2mths with 1500km of that done in 3 days (towing) so haven't had a chance to wear out the back tyres yet, besides it only gets driven 50-100km in a normal week so i'll have traded it in before it reaches 50,000km.

Only Commodore/ute that can really tow properly is the VZ Crewman crew cab which has a live rear axel and 2500kg towing capaity. Preferably with a V8.

The VZ SS Crewman has a lower towing capacity than my VE SSZ Ute.

Having said that. You will prob not have an issue cause you car/trailer is so light. The massive trailer and the zed on it where pushing 2000kg. It was a very long trip from QLD.

My trailer is rated at 680kg and my car is 560kg so 1240kg all up and usually around 150kg of tools n stuff in the ute tray. You have to look in the rear view mirror and see the car on the trailer to remind yourself that you are actually towing something.

My previous tow car was a 2000 Toyota HiAce 2.4L Auto with 85kw and 200nm (probably 65kw coz it had 350,000km on the clock) that thing struggled just to tow the trailer over speed humps.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
    • Also, I logged some data from the ECU for each session (mostly oil pressures and various temps, but also speed, revs etc, can't believe I forgot accelerator position). The Ecutek data loads nicely to datazap, I got good data from sessions 2, 3 and 4: https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-2?log=0&data=7 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-3?log=0&data=6 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-4?log=0&data=6 Each session is cut into 3 files but loaded together, you can change between them in the top left. As the test sessions are mostly about the car, not me, I basically start by checking the oil pressure (good, or at least consistent all day). These have an electrically controlled oil pump which targets 25psi(!) at low load and 50 at high. I'm running a much thicker oil than recommended by nissan (they said 0w20, I'm running 10w40) so its a little higher. The main thing is that it doesn't drop too far, eg in the long left hand fish hook, or under brakes so I know I'm not getting oil surge. Good start. Then Oil and Coolant temp, plus intercooler and intake temps, like this: Keeping in mind ambient was about 5o at session 2, I'd say the oil temp is good. The coolant temp as OK but a big worry for hot days (it was getting to 110 back in Feb when it was 35o) so I need to keep addressing that. The water to air intercooler is working totally backwards where we get 5o air in the intake, squish/warm it in the turbos (unknown temp) then run it through the intercoolers which are say 65o max in this case, then the result is 20o air into the engine......the day was too atypical to draw a conclusion on that I think, in the united states of freedom they do a lot of upsizing the intercooler and heat exchanger cores to get those temps down but they were OK this time. The other interesting (but not concerning) part for me was the turbo speed vs boost graph: I circled an example from the main straight. With the tune boost peaks at around 18psi but it deliberately drops to about 14psi at redline because the turbos are tiny - they choke at high revs and just create more heat than power if you run them hard all the way. But you can also see the turbo speed at the same time; it raises from about 180,000rpm to 210,000rpm which the boost falls....imagine the turbine speed if they held 18psi to redline. The wastegates are electrically controlled so there is a heap of logic about boost target, actual boost, delta etc etc but it all seems to work well
×
×
  • Create New...