Jump to content
SAU Community

Recommended Posts

  • 3 weeks later...

Dude get this on the ground already so we can go cruising like in the old days and hold up traffic for ages hahaha

it's been on the road.......for a month and a half before clutch problems. I'm up for another bogan cruise if you are. bring on the mullets wigs!

If you're thinking of selling them...

i don't need'em, wouldn't you have a set on the r33 already anyway. aren't r33 gts-t's pretty much the same as non v-spec r32 gtrs?

it's been on the road.......for a month and a half before clutch problems. I'm up for another bogan cruise if you are. bring on the mullets wigs!

i don't need'em, wouldn't you have a set on the r33 already anyway. aren't r33 gts-t's pretty much the same as non v-spec r32 gtrs?

Oh hmm... I should look into that factor...

I was shown the other day some nice 8 pots that a member uses on here for racing with... able to purchase the full kit for $1,500 brand new...

I'm keeping my eyes on it, and might buy it very shortly...

So cool. Its a shame we cant have these like the yanks do... TT VH45DE :worship:

they are, when i was doing the research in to it for 450sx i found that the maximum boost-able engine size is just over 4.5 ltrs for a s13. i believe it's 60 cc within the range. these figures were calculated using the weight of 1140kg stated as the factory weight times the factor of 4.82 for na and 4.0 for boosted. from the following link. the ADR limits are slightly different.

so the maximum turbo or supercharged engine in a 180sx can be 4560cc and 5494cc for naturally aspirated.

so imagine the engine that will able to go in a 1500kg skyline.

http://www.rta.nsw.gov.au/registration/downloads/vsi/vsi_06_-_guidelines_for_light_vehicle_modifications_nov_2007.pdf

they are, when i was doing the research in to it for 450sx i found that the maximum boost-able engine size is just over 4.5 ltrs for a s13. i believe it's 60 cc within the range. these figures were calculated using the weight of 1140kg stated as the factory weight times the factor of 4.82 for na and 4.0 for boosted. from the following link. the ADR limits are slightly different.

so the maximum turbo or supercharged engine in a 180sx can be 4560cc and 5494cc for naturally aspirated.

so imagine the engine that will able to go in a 1500kg skyline.

http://www.rta.nsw.gov.au/registration/downloads/vsi/vsi_06_-_guidelines_for_light_vehicle_modifications_nov_2007.pdf

I think you'll find you're using the wrong value aren't you? Aren't you meant to be using the bottom one? 5.46 and 4.68 for N/A and Turbo respectively? Isn't mono constructed like those one off builds/kit cars?

i don't need'em, wouldn't you have a set on the r33 already anyway. aren't r33 gts-t's pretty much the same as non v-spec r32 gtrs?

they are basically identical imo, 300mm vs 298mm rotors and the same calipers or something like that, nothing in it.

Edited by Rolls

I think you'll find you're using the wrong value aren't you? Aren't you meant to be using the bottom one? 5.46 and 4.68 for N/A and Turbo respectively? Isn't mono constructed like those one off builds/kit cars?

mono constructed is the modern way to make car chassis, it's dual constructed if its body can detach from the rails, like model t ford. unless your making a hot rod? at least i think that's what they mean.

  • 2 weeks later...

hey dude quick question, what spigot bush did u use for the 300zx box conversion? did the new one need any machining to fit in the 45 crank? also wherew did u get those UAS engine mounts? nice car man 190kw with headers mad shit

Edited by akaaa7

You make it sound so easy lol.

Wish it was so easy! I knocked it out with a cold chisel from memory, you could also mig weld a metal bar to it and lever it off...

I like welding stuff! :thumbsup:

Get that damn car on the road Farch!!

And, nismo used to sell side skirts for your 180! they look good as I saw on today.

If the spigot bush has a hole drilled the whole way through it, you can try the old trick of filling the bush with heavy duty grease, and then hammer a steal bar that is machined to fit perfectly into it. The grease makes a perfect seal, and it can't be compressed, so it pushes the bush out.

That's if the bush is hollow the whole way through. If not... Too bad, so sad. :P

Don't know if it's been mentioned, but torn up paper poked into the hole (newspaper works great), then punched (same principle as grease method) in with a hammer & punch works very well. Then you just flick out a mashed up wad of compressed paper fiber.

Clearances need to be very close for grease method to work, otherwise it just pumps out around the punch; much less important with torn up paper.

Amazing build BTW; love the execution.

about 7 months ago i hit up ross tuffbond to make a custom balancer and was told it would take 6 weeks, the six week came i rang up and was told haven't had time. I gave up, and completely forgot about it, thinking it was never going to happen. well i got a call last week and this was apparently just finished!

post-38774-0-49979500-1310713393_thumb.jpg

  • 3 weeks later...

Well we got the gearbox back together finally.

And the new intake setup is sorted too. We found that the BMC filter setup was too restrictive for the engine, so that got the boot and a replacement was found.

That involved going to autobahn and ordering the biggest k&n filter we could get our hands on with a 90mm outlet.

Then massaging (hammer :whistling::) ) the engine bay to fit the mammoth filter, which also required the 90mm airflow meter to be chopped.

All fitted sweet in the end and the car now goes even better. Farch will explain his test drive later....

The 20cent coin in the second pic gives you an idea how big this thing is!!

post-12712-0-19192500-1312109292_thumb.jpgpost-12712-0-64981700-1312109301_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
×
×
  • Create New...