Jump to content
SAU Community

Recommended Posts

Hi just and update,

Be a slow process these last few weeks, not much left to go before we can crank the big bitch over for the first time.. Has got 15L of penrite run in oil, in the dry sump tank ready to rock. So the last few days iv been doing all the tidy up jobs. Not long now!!

39555_1682517349894_1446408764_31709648_2660343_n.jpg

148701_1682518109913_1446408764_31709649_4374651_n.jpg

76521_1682518389920_1446408764_31709650_557919_n.jpg

just a quick question: when the engine torques will it do damaged to the top rad hose as its vertually rigid? Looks great though!

the wiggins clamps actually do have an amount of flex in them. I think it should be ok.

great build mate. should be a very, very, very fast car. :P Love that it's still a 2.7 and not a 30. I think for what you want a 2.6 or 2.7 is the way to go as you will want revs and lots of them. :devil:

what kind of gearbox are you going to run in it?

there's a little expandable piece inside. hard to explain but if you've ever held one in your hands and played with it a bit you'll get the idea. it's not a huge amount but they do allow both flex and twist without leaking.

The clamps have a fair amount of give in them, they are rubber o'ring sealed on a feral, the are a pain in the arse to put together but are extremely well made as these are the genuine Adel Wiggins clamps, the 4" clamp was worth $600 and thats each. If you you look at any top notch race cars, weather it be Ken Blocks Fiesta, GT Cars, majority of them run them.

0702_impp_09z%20wiggins_clamps%20tube_connectors.jpg

^^^ ive been tracking kier wilsons gtr since when 1st started back in early 2000...it reminds me of my silver aust delivered gtr & the sound of a 3ltr - well, nothing beats it, sounds like my current gtr :devil:

  • 2 weeks later...

Hi Guys

Another quick update for ya's, engine work is nearly complete, the wiring loom will be finished on thrusday, once thats done just gotta do brake lines and a few other tidy up jobs. Tomorrow we will be test fitting all the body panels and checking the lines of them all and adjusting them so they look shit hot. Here's some quick pics of the engine in its final stages (sorry about poor quality, get some better ones tomorrow).

76951_476525668484_679318484_5674207_1629630_n.jpg

76382_476525708484_679318484_5674208_6977286_n.jpg

150583_476525738484_679318484_5674210_6006185_n.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
×
×
  • Create New...