Jump to content
SAU Community

Recommended Posts

TS Astra I think I got mine from running in a front wheel drive rally car. Despite the short sighted people around... they have been in use in the Off Road Racing for many years for all the positive reasons mentioned.

The standard Holden Astra one is as robust as any on the market and given most people don't know what they are you can pick one up from a wrecker for as little as $250.

For the people who have not seen one they are power assist and have better feel than any Nissan (or any other) mechanical pump. They ramp up the pressure when needed and run in an idle state when nothing is happening. Mine is wired to a switch on the dash so I can turn it off when on the dyno.

If someone gets one and needs a hand with the wiring I can dig up something as it is as not straight forward with more than 1 power wire and from memory the wire colours are odd.

  • 8 months later...

Josh's 180SX has an astra pump fitted as there was no room to put an engine driven pump onto the VH45DE.

It's been wired up to run constantly, and works very well, but I think it would be better if it did have a controller (lucky the alternator is a 110Amp unit on the v8).

  • 2 months later...

well the astra pump works ok.

i installed one in the uas zed. its quite heavy. and on full lock it draws 75AMPS, at idle with no steering its about 25A.

these pumps were designed to be mounted very near the rack. one thing ive noticed is a slight lag in assistance as its mounted in the boot and has 4 odd meters of hose to the rack. (any hydraulic gurus chime in) we used -4 teflon. mayby -6 with a restrictor would of been better but once your going it feels fine.

they run at full speed 100% of the time. the electronics inside keep the pump at a constant rpm and feed in current to compensate for the pressure.

try using a simple accumulator... should be available from any available hyd supply joint. It just picks up the initial demand.

J.

HAHA good idea, gonna steal that idea :P

  • 5 years later...

Have plans (as in interested, talked a bit, done nothing towards acquiring the bits yet) for an R chassis and an S chassis, with the Astra pump setup and a steering quickener.

Main identifiable issue is lag on the assistance - unknown just how much flow capacity is available from the electric pump vs even a standard engine driven pump.  Neither is really spec'd for motorsport application.

They fit under the driver's side battery tray nicely. 1m run back to the rack, botlt them to factory GTR bov points.

Have a dumb unit, do wonder about getting a CAN one and if you could control it better than the internal logic on the dumb one.

Car hasn't really been run with it yet so we'll see how it goes

I would be really interested if anyone ever attempted to adapt a modern servo electric system to a Skyline, e.g. one of these Bosch units which are found in many modern cars:

http://www.bosch-automotive-steering.com/en/products/car-steering-systems/electric-power-steering-servolectric.html

I like the simplicity of these systems. I would imagine the control/electronics side of things might be the challenge given how different the steering feels on many similar models these days (e.g. different Porsche 911 variants), simply due to software changes.

 

  • 4 weeks later...

Hi, my stock belt driven P/S pump got a ripped hose under driving, the pump failed quickly as a result of that.

So, since it was hard and expensive to get a new pump here in Norway, I found a electric P/S pump from Mercedes A-class, wich got a reservoir in it, and that makes it easy to place around. Only require + and - power the way i installed it, so Hook it up with a relay and a switch, or on IGN. I found that this works very well for my daily driving, but I havent tried on track yet.

 

s-l640.jpg

  • Like 3

Acrula, which pump do you think is heavier the nissan one or the A-class? what car do you have? any pictures of where you mounted it?

I've weighed an rb26 pump and I think it was 2kgs, just the pump no belt, bracket or lines but I will double check.

I'm thinking of sneaking one in under the starter motor, even if it weight is close to the same, having it lower and further back would be nice.

Think I might head down to a wrecker and ask them if I can look at and weigh every type of electric pump they have.

Edited by aleks

Pretty sure that and all others would be to tall to fit there. 

Astra one is not light. Would be more than pump+bracket+belt+lines+res 

A class one looks a tad lighter

On 23/04/2017 at 5:48 PM, Acrula said:

I found that this works very well for my daily driving, but I havent tried on track yet.

Is there any difference in steering feel now that you are using the electric pump?

I agree Justin that a class one looks too tall, but I meant to try and fit another, smaller powersteering pump under there.

Going to try and get a hold of a toyota mr-s power steering pump. The astra pumps look abit too big/heavy for my liking plus I dont want to dirty my car with an opel part.

I just weighed a gtr pump with the pulley, belt, bracket and bolts and they come in at 4kgs.  Will weigh the lines and resevior and lines when I pull it off.

  • 2 weeks later...
On 1.5.2017 at 10:11 AM, JustinP said:

Is there any difference in steering feel now that you are using the electric pump?

Sorry for late reply. Not on this forum that often. I dont feel any difference at all under normal spirited street driving, but I have not tried it at the track yet. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...