Jump to content
SAU Community

Recommended Posts

i cannot believe no one has given him the most important advice.

make sure you run very good engine oil. Motul 300v chrono is a must for a track day. if you don't chances are you will spin a bearing

its the old saying..."if you don't want to spin a bearing...put Motul in it!"

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

I would make sure your number plates are both off. I know that insurance investigators often go to trackdays armed with cameras to catch out somebody who has an incident so they cant make a claim

i cannot believe no one has given him the most important advice.

make sure you run very good engine oil. Motul 300v chrono is a must for a track day. if you don't chances are you will spin a bearing

So are you saying that spun bearings much more likely due to oil film breakdown than oil starvation? I would have thought the reverse was the case.

One thing you might want to do is get some Redline Water Wetter. Add it to your coolant to slightly help it from boiling. It aint too expensive and works well. I'll definetely be adding it to my system every track day.

ha i didnt know insurance people go that far with their jobs.

Yes, the head honches will even follow you into a public toilet to take a urine and stool sample for analysis; testing for booze, drugs n maybe even a hot curry/kebab with extra garlic sauce to prove the accident was your fault.

yes he runs motul 300v LEMANS

100% agree

for the engine with a little blow buy the lemans.... it is the shit!( and cost the same as the chrono)

i recomen in all breathing gtr motors (high HP it would help as well i guess)

chrono for the non breathers...

on a side note spun bearings are a combo of oil level and oil temp

the motul wont fix the oil level problem(it would make it worse as it cost a bomb) but it certainly keeps it together at higher temps for constant times

Isn't Chrono abit extreme for the OP (roughly no more than 200kw with the mods listed), I'd probably recommend it for 300kw, but for a engine putting out approx 200kw a very good semi synth or a full synth (like Motul 8100) will do imo. What's the story with full synthetics, is it true they don't protect all that well after a fresh oil change, takes about 1000km before they're fully effective?

Isn't Chrono abit extreme for the OP (roughly no more than 200kw with the mods listed), I'd probably recommend it for 300kw, but for a engine putting out approx 200kw a very good semi synth or a full synth (like Motul 8100) will do imo. What's the story with full synthetics, is it true they don't protect all that well after a fresh oil change, takes about 1000km before they're fully effective?

that is what is known as a 'load of shit'. Oil works best from the moment it leaves the bottle. Hell, I'm lucky to do 1000kms between oil changes. If you want a performance synth oil a bit cheaper than the 300v, Get some Royal Purple 10w40. ERD sell it for about $80 per 5l bottle I think.

i cannot believe no one has given him the most important advice.

make sure you run very good engine oil. Motul 300v chrono is a must for a track day. if you don't chances are you will spin a bearing

make sure your pads and rotors have plenty of meat left.

make sure all levels are good and a nice set of rubber.

make sure your pads and rotors have plenty of meat left.

make sure all levels are good and a nice set of rubber.

thats what i was thinking..it doesn't matter if the quality of the pad is the best u can get as long as there is plenty of pad on it. it will be fine for one day at a track.

As long as the oil levels are on high enough on the dip stick even with stock oil it will be fine...

What ever you do... don't even consider going out on the track without bleeding the brakes with a dot 4 fluid. Secondly, personally I wouldn't go out on the track without some pads that at the very least are sports pads that can take a bit of heat... ie. bendix ultimates at the very least but even they are very ordinary pads.

As somebody said before, if you can't stop trust me the day will just be scary, you'll have no fun and probably crash the car.

As long as the oil levels are on high enough on the dip stick even with stock oil it will be fine...

What ever you do... don't even consider going out on the track without bleeding the brakes with a dot 4 fluid. Secondly, personally I wouldn't go out on the track without some pads that at the very least are sports pads that can take a bit of heat... ie. bendix ultimates at the very least but even they are very ordinary pads.

As somebody said before, if you can't stop trust me the day will just be scary, you'll have no fun and probably crash the car.

Couldnt agree with you more. The day just gets scary and un-enjoyable when you find the car isnt stopping when you want it to. And the more you try thw worse it gets. Untill that one time... :/

I use Motul RBF 600 in my R33, and it hasnt let me down yet, even with "sport" Ferodo's on there. Have been meaning to get something a little heavier for the track.

Honestly,

I think your better off going to QR on the 6th of october for the Nissan Day!

Have you worked out who is going to tow it home!?!?

Sorry mate just playing around, i have seen way too many blow up though.

Thats why i got an evo for track. i will be driving a 32 GTR on the day though

Fingers crossed!!!

Edited by Duncan1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
    • Drain it. I got official Matic D but you can get whatever is listed as Matic D compatible.
    • Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
×
×
  • Create New...