Jump to content
SAU Community

Jacking Up Ur Car

kikutaknight

By kikutaknight,
in WA Wasteland

 Share

Recommended Posts

kikutaknight Enthusiast

kikutaknight

Posted
Posted

I've seen pictures of people with their cars jacked up two wheels at a time with the jack somewhere in the middle...

also cars jacked up from somewhere other than that little bit on the side made for those dodgey little car jacks.

i've looked around on the bottom of my car but can't figure out exactly where people are putting these jacks. can anyone upload pictures or something for me? :D 

would be appreciated...zorz.

Link to comment
https://www.sau.com.au/forums/topic/289799-jacking-up-ur-car/
Share on other sites
260tech Proficient

260tech

Posted
Posted
I've seen pictures of people with their cars jacked up two wheels at a time with the jack somewhere in the middle...

also cars jacked up from somewhere other than that little bit on the side made for those dodgey little car jacks.

i've looked around on the bottom of my car but can't figure out exactly where people are putting these jacks. can anyone upload pictures or something for me? :P 

would be appreciated...zorz.

Check out this thread. http://www.ehow.com/video_4941952_put-jack...er-vehicle.html

Stay safe.

GW

Stinky Rooster Grand Master

Stinky Rooster

Posted
Posted

That vid misses quite a few vital safety aspects, like making sure the non-raised wheels are chocked properly for one...

Firstly, never ever ever try and use a sill jack on any other part of the car other than the proper jacking points. As Bard said, a road car is not strong enough to do this and you will either destroy the jack or your car. Heck, if your lucky, maybe even both!

If you want the front lifted then use the centre of the cross member - not the sump! Always use jack stands and try to keep them as close to the suspension pick up points as practicle as possible. The control arms used in that vid are a good idea, although I cant say using the edge of them is that bright. Personally I would use a bit of wood between the jack stand and the control arm (steel on steel is asking for trouble IMO) then you can use the whole control arm not just the edge.

For the rear, try putting the jack under the diff housing. Just be aware that the car will be VERY unstable as it is being jacked and can rock from side to side.

It should go without saying that safety should always come first. Never get under a car that is supported by a jack, always make sure the car is on level ground before raising it at all, and try to keep bystanders right the f**k away. One other person as a spotter is a good idea, but that should be it. Always fully chock any wheels that are to remain on the ground. Also, try not to open any doors on a car that is supported by a jack. Especially on 2 door cars, this can really upset the balance of the vehicle. Lastly, as I said before, its always a good idea to use wood between any steel jack or jack stands and the car. Apart from adding a "crush" factor that helps with stability, the friction coefficient is much higher making it more stable.

  • 3 weeks later...
  • 1 month later...
08yannch Rising Star

08yannch

Posted
Posted

+3 for the diff or x-member/rad support :laugh:

also i use the OEM jack on one of the sides so if a stand does fail the car wont fall all the way 2 the ground.

also never use bricks 2 suport a car i made that mistake once and i will never do that again :)

JonnoHR31 Grand Master

JonnoHR31

Posted
Posted

spare wheels and tyres are really good for getting a car up off the ground, if your doing something that doesnt require removing any of the wheels you can simply jack it up via the diff/xmember and chuck a spare wheel and tyre under each wheel, 2 if you need to go really high. if the wheels need to come off you can put the wheels and tyres under the chassis rails, make sure you have the car sitting on 4 points before you get under there and dont have the front supports too far back, the motor is the heaviest part.

08yannch Rising Star

08yannch

Posted
Posted

car ramps are good 4 doing work on a car when u don't need 2 take off the wheels and also there is no ramp solution 4 raising the whole car unless u make some.

4 me im restricted when it comes 2 space so im stuck with a trolly jack and axle stands (modified 4 skyline)

08yannch Rising Star

08yannch

Posted
Posted
with the height of the average skyline ramps would need to be about 8 feet long to be much good to ya

unless you remove the front bar or something????????

well all u do is wedge a thick bit of wood in there to extend the length

 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • drifter17a
      Rb25 trigger kit and timing misalignment

      By drifter17a · Posted

      The trigger kit I have is similar to the one in the link below. While going through Facebook, I saw someone else mention a similar issue, and I’m starting to think this could be related to the crank gear itself. I understand these parts are CNC machined, but maybe some earlier versions or individual pieces might have slight inconsistencies—it just doesn’t look right in my case. https://www.facebook.com/share/16an8evZd9/?mibextid=wwXIfr I originally installed the crank gear using the thin OEM washer, but as shown in the attached photo, the timing belt walks very close to the edge. When I tried using a Nitto washer—which is thicker—it actually made the issue worse. The belt walks about 1mm off the front edge, which raises more concern about alignment.   I’ve gone through the full process of elimination:   The tensioner pulley and bolt are brand new and installed correctly. The bolt isn’t bent and is oriented properly. The back of the tensioner and the idler pulley are clean and seated correctly. The idler sits slightly more forward, which I understand is due to its design. I’ve experimented with both tight and loose belt tension, but it makes no difference. As soon as the engine runs, the belt immediately walks forward again—even if I reset it beforehand.     At this point, I’m considering replacing the crank gear with your Race Version 1 (12-tooth), but before purchasing, I wanted to ask:   Are you aware of any alignment issues when using this gear? Would this gear help keep the belt aligned correctly, or could the walking still occur? Does it work with a standard missing-tooth crank and rear washer? Is there any specific crank setup or install procedure required?     For reference, I’m not using a front washer, as the PRP crank gear seems to replace the need for one.   Looking forward to your advice.
    • PranK
      ATCC Amaroo Park 1987

      By PranK · Posted

      Yep, looks that way. Never driven an E30 or R31 so I can only imagine  
    • Dose Pipe Sutututu
      Rb25 trigger kit and timing misalignment

      By Dose Pipe Sutututu · Posted

      Post up some photos
    • GTSBoy
      WTB RB25 Gearbox NSW / central west

      By GTSBoy · Posted

      Yuh, My new R34 box is sitting on the workshop floor (in its large shipping box, which is a nice thing on its own), along with a front plate to convert to push clutch. There was no way I was interested in rebuilding my existing one. Was only partly interested in the risk of buying a used one. But, if you want a 2nd hander, I can point you to one in/near Melbourne at least. @Komdotkom has one that should be in good enough condition to be usable. I don't think it's in a for sale thread, you'd have to message him. @redzedhas one that definitely needs a rebuild.
    • Watermouse
      ATCC Amaroo Park 1987

      By Watermouse · Posted

      I used to love going to Amaroo to watch the HQ series go for broke (eventually stopped due to lack of spare parts) and also the Porsche series.  It was so cool to back your car up to nearly the edge of the viewing barrier and party with your friends, having a bbq and alcoholic/non drinks. It was such a family/mates atmosphere
×
×
  • Create New...