Jump to content
SAU Community

Recommended Posts

Chris I'm getting Nepean Smash Repairs out at Emu Plains to redo my front bar. Terry recommended him after I hand a ding in my rear quarter. He knows how to mix midnight purple perfectly.

104 Russell Street

Emu Plains NSW 2750

(02) 4735 3522

Might be a bit of a trek for you from Wollongong but I don't know of anywhere else in Wollongong where you could go.

Cheers,

I just ended up taking it up to Bodyform today.

It's a decent drive but with his rep I'm confident it will turn out good.

I was just too worried some one down here would butcher it

Spotted Jennie's white R34 at work this morning.

26092012096.jpg

They look great next to each other! :-) Wont need to check my passanger door for dents today either. Haha have a great day!!

They look great next to each other! :-) Wont need to check my passanger door for dents today either. Haha have a great day!!

For that exact reason, it's great when you get to park next to someone you know :)

For that exact reason, it's great when you get to park next to someone you know :)

That's right! Some people aren't as careful as others with their car. I am always careful not only so I don't hit another car but also so I don't damage my own! With a GTR next to me I don't need to worry. :-)

Waved to a silver S2 R33 in Albion Park today.

Not sure if wave returned, was checking for SAU stickers.

Near croome rd? Caught me off guard but i gave a nod... Ch'ur bro style.

My cars been playing funny buggers lately but I had intentions on going on last pizza cruise but carputer said no. Whens the next one?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
×
×
  • Create New...