Jump to content
SAU Community

Recommended Posts

Where's all the Skylines that haven't entered,,,get off ya lazy bums and enter your car. GTR's,,,everything and anything that starts with "GT" and the best one of the lot the beautiful R33 GTS-t's???.

My car starts with a "G" but doesn't have a "T" in it, can I still come? :)

I'll pay/fax around Thursday-ish

  • Replies 164
  • Created
  • Last Reply

Top Posters In This Topic

My car starts with a "G" but doesn't have a "T" in it, can I still come? :down:

I'll pay/fax around Thursday-ish

Oh my bad,,,my very bad,,,hows about this,,,if it starts with an N and ends in an N or starts with a D and ends with N they are very welcome.

Thats closer to what we want,,,those cars would be rad.

Neil.

I'm entering my old girl,she is bound to win most beat up. :)

Look forward to seeing her there J. Colour reminds me of SpearOmint Life Savers :P .

Because these cars will be displayed in a covered area, there won't just be an assault on the eyes. It'll also be an assault on the ears!!!!!!!!!!!!!!!!!

So any vid should of course catch the SOOOOOOOOOOUUUUUUUUUNND of these machines coming and leaving eh what?

i want my gtr there but need coilovers yesterday its undrivable n i been hangin for 2 years plus for this.Im so cut i want my car there anyone wanna lend me some coilovers for the day so i can get my nugget to the show?

sure....whatya need just standard stuff to get it moving?

genelle....i reckon my race car can give your's a run for worst in show....shes got a fair few scrapes and scratches up close these days

sure....whatya need just standard stuff to get it moving?

genelle....i reckon my race car can give your's a run for worst in show....shes got a fair few scrapes and scratches up close these days

Have you got a rear quarter dent?

Most of the front bar paint missing?

Dropped a motor on the radiator support?

Dropped a gearbox on the front bar?

Cause I have... :thumbsup: LOL

Must fax shit off and pay for stuff tomorrow I think

might see if i can trailer down the 32......waiting on parts from japan and usa....dont know if it will b ready...new turbo should b here in the next one or 2 days tho

drag it on down.....it doesn't need to be able to drive to take part :bunny:

i got coilovers lol so ill rego the nugget n it will be there also can we pay at gate or not?

we'd strongly prefer entries before if at all possible so we can organise layout, space etc.

So what time is everyone expected to arrive by & when is the actual kick-off?

Theres a bunch of us coming down from Newie / The Coast, gonna be meeting up in a few places, including the Twin Servos.

So what time is everyone expected to arrive by & when is the actual kick-off?

Theres a bunch of us coming down from Newie / The Coast, gonna be meeting up in a few places, including the Twin Servos.

Entry is from approximately 8am, and the show kicks off at 10am - it's a pretty big area, so it's going to take some time to get everyone organised...

Question for the organizers...

I've been plugging this event on another forum (JDMST) and there's a few attendees from there - a few have come back with concerns about the entrance to the venue being pitted with massive speed humps.

Have any of the organizers addressed this, or have some secret entrance that the rest of us should be aware of and use on the day?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...