Jump to content
SAU Community

Recommended Posts

Ok here is a question for you fellas that track your 300kw Skylines.

I've been changing the oil after every track day. My GTR makes about 290 kw and has oil catch can, oil cooler, bigger radiator and runs 14-18 psi lo/hi boost depending on the type of track I'm driving.

After about 10 minutes of track time my oil temp is 120 where I do a cool down and come in.

Since the oil temp is so high and on boost for so long I've always felt it is a good idea to change the oil right after coming home from a track day. Always been the first thing I do.

So my question - do you fellas do that too? It is getting a bit expensive cause I only use Motul 300v or Mobile1 Full Syn - so about $100 for an oil change. This on top of track fees, brakes, petrol and tyres. If this is the cost then I'd rather spend $100 preventing oil related engine failure than $$$ for a rebuild. But just want to know how you folks go?

I know a lot of other guys just do normal 5k and don't change their oil after every track day.

Link to comment
https://www.sau.com.au/forums/topic/295705-replace-oil-after-every-track-day/
Share on other sites

I change oil every track day, but i do it the other way around. I change the oil before every track day. That way i know i have anice fresh sump and filter before every track day and oil that is in decent enough condition for pottering around on the streets, which lets face it, you can barely gas secon gear on the street so hardly stressful for the engine or the oil you are running

I change oil every track day, but i do it the other way around. I change the oil before every track day. That way i know i have anice fresh sump and filter before every track day and oil that is in decent enough condition for pottering around on the streets, which lets face it, you can barely gas secon gear on the street so hardly stressful for the engine or the oil you are running

I change my oil every 10 minutes...about how long my engine runs at a meet. :banana:

With around 20K in engine parts invested (my labour is free as i build them myself) a $250 oil change ($25 a litre plus filter) is cheap insurance. I use Motul 300V 'Le Mans' 20W60 and built the engine to run this oil weight.

If it picked up a bearing and or threw a rod and i didn't do this id be always thinking whether if i had done the oil if it would have happened.

Edited by DiRTgarage

I also change my oil before every track day, I dont want to spin a bearing like many others have. I rarely drive my car on the street so i'm not worried about having track day oil in it.

Hmmm, seems to make sense doing it before but means I'm going to go through twice as much oil changing before and after. Maybe I should keep the "street" oil and put that back in after a race day but only run on the race oil for just that track day.

Another expense of having a track/daily driven car. Oh well, need to take care of the beast.

Dont worry about after. Seriosly, if you have done a track day on a sump of oil then i dont see a problem with running it for 4,500-5,000kms. Temp and contaminants are what hurt oil and i cant see you getting too much f either sitting in traffic or going for a drive on the street.

If you run standard or extended sump definatley change before every track day. I personally change my oil every 2-3 track days as I run a dry sump set up with water to oil cooler set up in the radiator end tank so i run around 12-15lt of oil in total inc lines and cooler and the oil temp never sees over 110 deg. Heat is what kills oil so if you can keep the heat down that will go a long way to keeping your oil healthy.

We used to do the oil change just before every track day when i was running the Royal Purple 10w40. When we changed to the RP41 racing oil, we were able to start using the oil for 2 track days as long as I don't do a lot of street k's between them (1000 - 1500). The oil is still seeing < 2500km's total and when we send it away to be tested all results are A-OK.

We did a test where we changed the oil, did about 200k's street, then a track day, (so, <500ks total) sent the oil away to be tested. Drove the car for 1200k's street, did another track day, another few hundred k's on the street, and sent away another oil test. The only difference between the 2 samples was a tiny bit more fuel dilution (about half a percent up from 2.5 -> 3).

Im new to the game but I change it before the track day, Mines a quasi daily as it only comes out if its raining or if I go for a cruise with my daughter and such.

Or if its cold

Or if it hot

Or I have the need, the need for speed (sorry).

I figure it is the combination of heat and lots of boost that might degrade my oil. Basically 110-120 every session for 5-6 sessions over 120k's and a fair bit of boost. I thought that the boost will create bigger compression and therefore more blowby past the rings into the block - e.g. more contaminents. Also I use a return style catch can and get a fair bit of oil/air mix com'n out of the breathers then draining back in.

All good advice here folks I will probably switch to doing the oil change before the track day.

I change oil every track day, but i do it the other way around. I change the oil before every track day. That way i know i have anice fresh sump and filter before every track day and oil that is in decent enough condition for pottering around on the streets, which lets face it, you can barely gas secon gear on the street so hardly stressful for the engine or the oil you are running

HAHA...I'm in the same boat, I pretty much do the same.

  • 2 weeks later...

but seriously....change it before the track day, and after if the oil got hot. otherwise like roy said run it for ages on the street.

mine is track only so I change it every 3-4 days, which is normally 2-3 race meets.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 2 spots that my exhaust guy joined the 2 pipes together  Made a big difference. I'm now able to live with it. I can make it louder if I want by removing the HKS caps.
    • Hi all, considering clutch upgrade to support 1130 engine hp from 1650cc injectors on e50 at 85% duty cycle (1650 x (11.85/14.7) x 85%). Narrows down to these three as they can be converted to use gm 26 spline input shaft if I ever want to use transmission with that input shaft (orc1000f and r3c easy/cheap just change center hub; tr2cd pricier must change clutch discs). Pricing orc1000f similar to tr2cd, r3c about usd 200 pricier. Orc1000f triple plate 200mm. Tr2cd twin plate 215mm. R3c triple plate 215mm. Claimed max torque : orc 1000f 723 lbs ft; tr2cd 800 lbs ft; r3c 1100 lbs ft. Why orc1000f triple plate but claims lower max torque vs tr2cd twins? Is orc1000f underrated? Any info maxing out these clutches? Info on street/traffic driveability/pedal feel? Thank you for any info on them.
    • Some troubleshooting, connect up a timing light/gun with a proper ignition lead on coil 1. Hold the revs at 4~4500rpm and see if your timing is all over the shop, scattering off its tits. If so, there's a high chance your CAS is fked. But I read you have a Link ECU ready to go in, why not just skip all this and put that in - will make troubleshooting so much easier.  
    • Misfires when the car is fully warm are generally attributed to the coils (and/or the igniter, on cars with a separate igniter). They can stop working properly when they get hot for a number of reasons. Either electric/electronic, or from thermal expansion opening up gaps and allowing HV leakage. Seeing as you have replaced the coils, that could/should rule them out. But I wouldn't always assume so. Were the coils genuine? Or is there a chance you have bought some counterfeit Chinesium shit? Then we're back onto loom connections. They can fail when warm/hot for the same reasons. Inspections, cleaning of contact surfaces, ensuring that terminals are fully inserted, etc etc, are all justified. The same (heat effects) holds true for the other electrics and their connectors. AFM & CAS, primarily. If you try that Chinesium AFM, drive it around on low load until it is properly hot, but do'nt give it more load than you have to, except when you need to see if it will still miss. I'm dead serious about the untrustworthiness of the calibration of those copy AFMs. Injectors are unlikely to get hot unless the fuel is coming back around hot. You could try squirting them with compressed air or freeze spray to cool them back down to see if they are maybe the cause.
    • Alright, all the plugs looks good. Noticed that it starts to get bad when the car is up to temp, that's when things starts to misfire hard. next to do is Injector cleaning and such. Got in touch with a shop to do work on the injectors next Monday also help on diagnosis.
×
×
  • Create New...