Jump to content
SAU Community

Recommended Posts

ok hang on so the $2802 is what i pay per year and the "excess" which is $1600 is what i pay in an event of an accident etc? 3046 much safer than 3047 :P

what do yous pay then for your premiums?

With Shannons, Rating 1;

Cube - daily use cover, Skyline - extreme limited use cover, Pulsar - laid-up cover, approx. $170 per month.

If one's ecr33 diff has gone from a twin spinner to a single spinner akin to that of a VN commodore, what should one do?

options are:

shim

weld

replace with GTR diff

replace with real diff

all of these better than standard diff

options are:

shim

weld

replace with GTR diff

replace with real diff

all of these better than standard diff

Replace with GTR diff you say?

What benefit would this have over say, a train... which i can also afford.

options are:

shim

weld

replace with GTR diff

replace with real diff

all of these better than standard diff

Shim = what i will be doing

Weld = f**k that

GTR diff = will need to replace both half shafts as GTR is 6 bolt and GTST is 5 bolt

Replace with real diff = expensive and if u buy a shit one like i did it will explode nicely LOL

$10/month X 12 months = $120

is this your r33 or? why so cheap you must have a spotless license or something..

u think thats bad i remember being quoted somewhere round 5-6k full comp back in 2003 as a p plater r34 gtt think just cars or shannons.....

now $290 third party just cars.....

not surprised for a p plater i dont know what p plater would be able to afford that just for insurance anyway

With Shannons, Rating 1;

Cube - daily use cover, Skyline - extreme limited use cover, Pulsar - laid-up cover, approx. $170 per month.

thats not too bad for 3 cars but why do you need 3 cars for :/ i can understand 2 if you had 1 daily in which case i'd get a shitter thats not even worth insuring so i'd still only pay for 1

On a scale of 1 to Miley Cyrus, how illegal is shimming a diff?

you can shim a diff as tightly as you want, you can shim it for minimum lock or shim it so that it skips like a 2 way. Up to you.

With legality, its like anything if cops see it skipping they might say something, i have never had a prob with cops with the 2 way, they saw it skipping along the ground and didnt say anything

options are:

shim

weld

replace with GTR diff

replace with real diff

all of these better than standard diff

just went out for a drive to prac my heel and toe technique.......master :whistling: i notice that my diff feels a bit sad maybe its these f@#%in ku36's dnt like em time to get a real

diff nismo 1.5 or 2 way? yea boiii...

3 litre is probably cheaper

f**k welding the diff or GTR diff

either shim your current one or new kazz centre or nismo centre

do it once and do it properly

stuff changing in / out 2nd hand parts etc

kaaz 1.5

do it and you can thank me later.

shimming's good fun if you own a beat up 32, but if you want it to last, do it properly. Put it this way... ALL the power you make has to go through it. If you wanna wager that on a $1.50 shim go nuts.

shimming just increases the bite point of your viscous, which means there's still slip, as time goes on it'll wear down and cark your diff. Guaranteed. Unless you're prepared to pull down and flush pumpkins after every track day or major fang session.

kaaz 1.5

do it and you can thank me later.

shimming's good fun if you own a beat up 32, but if you want it to last, do it properly. Put it this way... ALL the power you make has to go through it. If you wanna wager that on a $1.50 shim go nuts.

shimming just increases the bite point of your viscous, which means there's still slip, as time goes on it'll wear down and cark your diff. Guaranteed. Unless you're prepared to pull down and flush pumpkins after every track day or major fang session.

why kazz? they better?

just went out for a drive to prac my heel and toe technique.......master :whistling: i notice that my diff feels a bit sad maybe its these f@#%in ku36's dnt like em time to get a real

diff nismo 1.5 or 2 way? yea boiii...

??? how else do you drive around? I heel/toe for daily driving.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
×
×
  • Create New...