Jump to content
SAU Community

Recommended Posts

anyone know of any GTR's running the PT6262 ball bearing with a T4 Divided .84 A/R with 3 5/8" V-Band discharge? would the .84 twin scroll be abit restrictive on the 26?

I have just bolted mine up today. The exact turbo u are talking about. Hoping to have it running by next weekend after i finish a 34 with PT5558.

I have fabbed up dump pipes for both and worked out cooler piping, plumb back pipes etc

efeef931.jpg

421f596b.jpg

This will be interesting Jez!

What's the specs for that 34?

Stock neo motor with Type B poncams and adj exh cam gear, link ecu with flex fuel tune, hybrid manifold, mvr 44mm gate, id2000's plazmaman ffp, DVS dump and plumbback pipe. Hoping to have it running and tuned early next week. Depending if Link arrives and also waiting on plazmaman plenum to be finished.

I was wondering whether you got the new turbo in yet, guess I have the answer.

How much boost are you going to run do you think?

That i will have to see what the engine likes when im tuning it. I will see how confident i feel with the power output as its a stock motor. Also running stock cams atm. I would like to see the differences in stock cams then type B poncams. Then i will think about doing variable cam once i have to upgrade the headgasket.

Very nice, shame its a stock motor as its probably not going to be able to show its real strength. I am assuming its a ball bearing 6262, and you are going to tune for E85?

Yes both are ball bearing. My rb26 i am trying to get as much response as possible which is why i went twinscroll 6boost manifold and .8 twin scroll rear. My old steelwheeled highflows came on hard around 4500rpm ad made 307 so i am aiming to better that

Yes both will be tuned on E85. They are actually both going to be be flex fuel tuned.

We understand the stock motors will be the limiting factor but not going to build the motorS until the time comes

My old steelwheeled highflows came on hard around 4500rpm ad made 307 so i am aiming to better that

Yes both will be tuned on E85. They are actually both going to be be flex fuel tuned.

Nice, very interested to see where it comes in - I've always had it in my head the PT6262 would be on the laggy side, though never been sure. If it can be all in before 4500rpm then that'd be fantastic :)

Stock neo motor with Type B poncams and adj exh cam gear, link ecu with flex fuel tune, hybrid manifold, mvr 44mm gate, id2000's plazmaman ffp, DVS dump and plumbback pipe. Hoping to have it running and tuned early next week. Depending if Link arrives and also waiting on plazmaman plenum to be finished.

That i will have to see what the engine likes when im tuning it. I will see how confident i feel with the power output as its a stock motor. Also running stock cams atm. I would like to see the differences in stock cams then type B poncams. Then i will think about doing variable cam once i have to upgrade the headgasket.

Are you going to stick with 2.5" out of the IC into the plenum or go 3"?

3 inch is pretty big Roy, I usually use 3 inch out of the turbo on builds over 400kw, I know it supports at least 550wkw from a car I did recently... 2.5 inch should be fine mate for either side.

I also fabricated piping for a built STI Liberty in 2 1/4 alloy, it runs 280awkw. More important is the cooler end tank design imo.

Just curious, mine are 2.5" and the numbers suggest that for 590cfm it should be fine with 2.5", but as always its interesting that the RB26 and GTR run 3" std

I see what u mean Roy, we will find out soon but i dont think the 2.5 will limit the setup. I think the only thing that will limit the setup is the standard internals

Very nice, shame its a stock motor as its probably not going to be able to show its real strength. I am assuming its a ball bearing 6262, and you are going to tune for E85?

the engine will take allot of abuse with that turbo on e85.... :P just dont be scared. These turbos come alive at around 28-35psi.

the engine will take allot of abuse with that turbo on e85.... :P just dont be scared. These turbos come alive at around 28-35psi.

Stre180 sr20vet made 'apparently' 760rwhp on a 6262 .63 housing it would want to be a low mileage 26 to even make 600whp reliable.

Stre180 sr20vet made 'apparently' 760rwhp on a 6262 .63 housing it would want to be a low mileage 26 to even make 600whp reliable.

I agree it would want to be a "known" engine but really 600whp is a walk in the park especially for a few dyno runs....if it was my own personal car like it is with jez i would have no problem running it regulary at 400rwkw. We see this power quite often on std 26 engines on E85. I reckon in realistic power @ 35 odd psi 700whp is achievable with that setup but i would stay sub 30 on std bottom end.... i still find it difficult to believe that 760whp result with the 0.63 housing.

Interesting that you mention that, someone I know hit 400awkw on E85 at around 22psi with his unopened <100,000km old RB26 and coolant started escaping places it wouldn't, I had thought it should be reasonably safely doable too... good to know there are plenty of others which have done so fine.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...