Jump to content
SAU Community

Recommended Posts

I went from a garrett gt42r with a 1.01 rear to a 6466 with split pulse T4 1.00 rear thanks to PJ.

at 24-25psi i went from 426kws to 415kws but gained 100kw in the mid range. difference between the two is night and day.

this is on a supra 3L stock motor and pump fuel only.

it coota it ran 125mph on a runway surface with the 6466 and at wsid with the 42 the best i managed was 121mph

I just watched a Supra getting tuned, it easily maxed the 700kw dyno. lol. Seems the 6boost manifold overboost issues are still common across the range. :/

Precision turbo but I didn't find out what size. I only know it was massive and had a 5 inch inlet.

I also helped get the VL RB30 started, and got the 6766 spinning. Is it common to hear bearing noise with the ceramic bearing cartridges? There is oil supply but the bearings sound flat spotted. Perhaps they need to get hot before the clearances close up?

Scotty. Was the oil restrictor removed? If it was you have almost certainly put the restrictor back in the wrong recess of the chra. There are 4 recesses and only one lines up with the restrictor. If you have it in the wrong one it pushes the chra out of round and you get this bearing flat spot noise and noisy bearing.

I also helped get the VL RB30 started, and got the 6766 spinning. Is it common to hear bearing noise with the ceramic bearing cartridges? There is oil supply but the bearings sound flat spotted. Perhaps they need to get hot before the clearances close up?

My 6466 sounds like this. After 500km its free'd up slightly but you can hear the 'tink tink tink' noise as the turbo spins down just before it stops completely. Still boosts fine and is plenty responsive. Might email Precision.

A mate's 6262 is quite noisy also but I thought it was just the thing with roller bearing turbos. It was actually really hard to spin when it first went on the car but seems to have free'd up nicely now. My brother's GT30 is noisy as hell, even after it was reco'd

I've had a buggered precision 6262 roller apart before and it only had one hole in the centre cartridge for the oil restrictor to locate into, the drain hole on the opposite side was more than half the diameter. Wonder if there's a few different assemblies they use

Dave thats going to be one result ill be anticipating, 6262 TS on a Neo doesnt seem to be existant out there. Is its just the turbo and lines your changing

ditching the DE runners for DET, 4 inch dump and highmount 6 boost, new ECU and getting my VCT back

current setup is lowmount Hypergear with DE runners and faulty ground on VCT which will be fixed when it gets the ECU

ditching the DE runners for DET, 4 inch dump and highmount 6 boost, new ECU and getting my VCT back

6 Boost? I hope the wastegate exit off the manifold is welded on the correct angle, Kyle won't entertain the thought his manifolds are badly designed, so won't fix the simple design flaw. You should be right though, as the boost spiking is the tuner's fault apparently.

Nice, lucky i didnt buy the runner off you. I just have to get a highmount mani then chase for gold.

I have two of them so you can still have the spare if u want it!

6 Boost? I hope the wastegate exit off the manifold is welded on the correct angle, Kyle won't entertain the thought his manifolds are badly designed, so won't fix the simple design flaw. You should be right though, as the boost spiking is the tuner's fault apparently.

you just had to make me go dig it out of its box and unwrap it just to check didnt you!

would of preferred a more even flow but a 90degree shouldnt be so bad.. if it spikes ill just run what it puts out! 35psi for all!

NDq8uYV.jpg

Got the car tuned the other day at Unigroup and the Precision 6766 is a weapon of a turbo. We opted for the 1.0 T4 split pulse rear end. We used to have a good old T78 on the engine, its an RB26, and at the same boost the 6766 is about 55rwkw up. All we changed was the turbo and dump pipe

We ended up with a consistant 485rwkw at 25psi on E-Flex which is currently showing around E60. Going to get some United E85 and see if we can crack 500rwkw with a bit more timing. I dont want to run any more boost so what it makes at 25psi is what its going to make ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...