Jump to content
SAU Community

Recommended Posts

my car is not running properly i think.. i only have minimal mods but it does not have much more than stock power wat could be wrong. it has a front mount, boost t 11pound , cat back 3inch zorst, heavy duty clutch. its only got 140atw.. could it be because of stock dump pipe???

Link to comment
https://www.sau.com.au/forums/topic/322133-car-not-performing/
Share on other sites

do you have any type of piggy back computer or aftermarket computer. if not then you cant expect much. your afr's will be all over the place and (most probably rich) . once you get something like a SAFC2 (fuel only) or power fc (ignition and fuel)your power will go up to realistic levels.

Blaming the ecu is an easy thing to do. Could also be the dyno reading low. Post up a dyno sheet.

I wouldnt say anything is wrong.

Do the basics first, ie servicing(plugs/oil/timing/ecu reset, etc).

Mine pulled 175rwkw with only a catback and a pod and 12.5degrees and was only running 9psi.

thanks guys i changed the dump pipe and im installing an eboost with a fcd within the next 3 weeks just need money for the tune.

even with the dump pipe changed i have noticed a big increase in spool and top end pull, so looking forward to the e boost :kiss:

the cat is a xforce one so i think its decent

Edited by havoc_r33gtst
Please please do not install the FCD. Do your car a favour and at least try and get a Apexi SAFC II

I've got an SAFC II if you want one - sitting on bedroom shelf. I used it when I had similar mods to you - works well and gives other info like voltage levels, knock, etc.

Id be going a compression and leakdown test before anything else.

180rwkw is a base figure for thos mods.

Personally for mild mods like that i wouldnt bother with an aftermarket ecu. Your not really going to get much top end power. Fuel economy would be better though.

Edited by Pattygtst

ive got 3inch turboback, profecb @ 11.5psi, fuelpump, fmic, pod, hiflowed injectors(unnecessary @ this stage), afc neo, made 197rwkw @ chasers then detuned to 193rwkw

tho it was just an afc it felt tad better to drive after tune

140 looks low friends auto made 150's with only pod and turboback @ stockboost

ive got 3inch turboback, profecb @ 11.5psi, fuelpump, fmic, pod, hiflowed injectors(unnecessary @ this stage), afc neo, made 197rwkw @ chasers then detuned to 193rwkw

tho it was just an afc it felt tad better to drive after tune

140 looks low friends auto made 150's with only pod and turboback @ stockboost

140 is way low..

mine made 186kw with dirty old apexi pod turboback and 11psi coutesy of a tap from bunnings...think it has a better fuel pump too..

Edited by Arthur T3
whats your compression like....

you need to find the problem not buy more shit...you should be getting around 180kw...something is wrong..fix it then buy more shit...

+1

you have a problem some where and an Eboost will not fix the problem.

  • 2 weeks later...

is there a way to raise compression if its down or is the car f***ed . could this be fixed if the mechanic i am going to checks it out ???? i bought it stock and then i got a boost tee installed the mech installed it and dynoed it he charged me 550 and it didnt seem to go much better even though boost was increased by 4 pound . since then i have changed mechanics but havent dyno tuned it ... should i ???

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...