Jump to content
SAU Community

Recommended Posts

my car is not running properly i think.. i only have minimal mods but it does not have much more than stock power wat could be wrong. it has a front mount, boost t 11pound , cat back 3inch zorst, heavy duty clutch. its only got 140atw.. could it be because of stock dump pipe???

Link to comment
https://www.sau.com.au/forums/topic/322133-car-not-performing/
Share on other sites

do you have any type of piggy back computer or aftermarket computer. if not then you cant expect much. your afr's will be all over the place and (most probably rich) . once you get something like a SAFC2 (fuel only) or power fc (ignition and fuel)your power will go up to realistic levels.

Blaming the ecu is an easy thing to do. Could also be the dyno reading low. Post up a dyno sheet.

I wouldnt say anything is wrong.

Do the basics first, ie servicing(plugs/oil/timing/ecu reset, etc).

Mine pulled 175rwkw with only a catback and a pod and 12.5degrees and was only running 9psi.

thanks guys i changed the dump pipe and im installing an eboost with a fcd within the next 3 weeks just need money for the tune.

even with the dump pipe changed i have noticed a big increase in spool and top end pull, so looking forward to the e boost :kiss:

the cat is a xforce one so i think its decent

Edited by havoc_r33gtst
Please please do not install the FCD. Do your car a favour and at least try and get a Apexi SAFC II

I've got an SAFC II if you want one - sitting on bedroom shelf. I used it when I had similar mods to you - works well and gives other info like voltage levels, knock, etc.

Id be going a compression and leakdown test before anything else.

180rwkw is a base figure for thos mods.

Personally for mild mods like that i wouldnt bother with an aftermarket ecu. Your not really going to get much top end power. Fuel economy would be better though.

Edited by Pattygtst

ive got 3inch turboback, profecb @ 11.5psi, fuelpump, fmic, pod, hiflowed injectors(unnecessary @ this stage), afc neo, made 197rwkw @ chasers then detuned to 193rwkw

tho it was just an afc it felt tad better to drive after tune

140 looks low friends auto made 150's with only pod and turboback @ stockboost

ive got 3inch turboback, profecb @ 11.5psi, fuelpump, fmic, pod, hiflowed injectors(unnecessary @ this stage), afc neo, made 197rwkw @ chasers then detuned to 193rwkw

tho it was just an afc it felt tad better to drive after tune

140 looks low friends auto made 150's with only pod and turboback @ stockboost

140 is way low..

mine made 186kw with dirty old apexi pod turboback and 11psi coutesy of a tap from bunnings...think it has a better fuel pump too..

Edited by Arthur T3
whats your compression like....

you need to find the problem not buy more shit...you should be getting around 180kw...something is wrong..fix it then buy more shit...

+1

you have a problem some where and an Eboost will not fix the problem.

  • 2 weeks later...

is there a way to raise compression if its down or is the car f***ed . could this be fixed if the mechanic i am going to checks it out ???? i bought it stock and then i got a boost tee installed the mech installed it and dynoed it he charged me 550 and it didnt seem to go much better even though boost was increased by 4 pound . since then i have changed mechanics but havent dyno tuned it ... should i ???

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of an update to this one. Having some issues on the dyno that held us back (boost spiking) and I want to pass some info over you guys and see what you think is wrong with my setup. The current readout on this dyno is 462rwkw on a low reading dyno so keep in mind it is a real world 500rwkw setup on a hub dyno. Don't read into the power figure too much as a sign of the issue. The short and curly of it is: 2.8 Litre Racepace build RB25 NEO N/A Head with VCT (internally standard however ) Borgwarner EFR 8474  Turbosmart 50mm Straight Gate + Mac valve 6Boost Manifold 4" dump to full 4" exhaust (nil restrictions) Wastegate plumbed back in and all angles in the exhaust system are acceptable and not too sharp. GFB SV52 BOV in cooler piping  Turbosmart BOV in EFR Housing   The issue we are having is it comes onto full boost for example at 4000rpm and spikes to 24/25psi, before dropping down to 17psi before slowly rising back up to the target boost of 23psi. It was extremely uncontrollable and the tuner actually had to ramp in boost progrssively with each 1000rpm on each boost setting we selected to try and reduce the amount of spiking. Sometimes we would see a drop of 10psi from the peak at the beginning of the run, to the low, until it took the next 500-1000rpm to stabilise back up to the target boost. The tuner is pretty confident that the straight gate is just a poorly designed product and leaks too much boost upon cracking the gate open and theres no way to fix it other than going to a poppet valve. He's also confient theres no ignition breakdown or floating valves. The fueling is extremely stable as well. Turbo speed is somewhere around the 109,000rpm area. The spanner in the works for me is that prior to this Borgwarner and StraightGate, the car was tuned on -5 twins at a diferent tuner, and he also had issues controlling the boost with it spiking around the same rpm range, so to me this sounds like the same issue and it can't be anything on the turbo side as this was all changed and I think the behaviour is extremely similar, if not the same. We also removed the mac valve and did a run on wastegate pressure and it still spiked and had the same behaviour. My thoughts on possibilities are: Boost Leak VCT Cam Gear isn't reliably activating consistently - (On this however, we did a run with the VCT disabled and the boost still spiked) Turbosmart BOV is not handling the boost? However this seems unlikely to not be able to handle 20psi. I have a couple of logs that I can't make sense of if anybody knows how to read them and can obtain further logs of other parameters if they are not enough, happy to pay for anyones time. The dyno readout with the power figure is the most recent last week. The other picture is from two weeks prior to that where we couldn't break 400kw (we removed the cat), however the issue of the boost control persisted. @Lithium @Piggaz @burn4005 @GTSBoy @discopotato03 I've tagged those that were quite active in recent pages here, no disrespect to those that know turbos well but I missed tagging. Cheers 
    • I recently purchased a 2018 Infiniti Q60, which has an SD card navigation map. I can see my system has options for real time traffic updates etc, and am wondering if there is something I can purchase to get this working? I can see there are at least updated maps for USA and Canada, but nothing for Australia. Surely Infiniti took changing road systems and city expansions into account when they decided to use an inbuilt navigation over Android Auto/Apple Car Play, or are we doomed to drive on streets that don't exist in the navigation system if you drive to a new area?
    • Luckily I didn't put in etch primer as I just found out it's not compatible with my body filler lol. Also just need to sand the panel anywhere between 150-400 grit so I'm in the clear there. It does say to not apply to soft old paint, I assume that means paint that is flaking, peeling,etc
    • @dbm7 and @GTSBoy thank you both very much! will give that a shot!
×
×
  • Create New...