Jump to content
SAU Community

Recommended Posts

Hey guys,

I went to a shopping centre today and there was like a promotion stand with people demonstrating a waterless car wash spray, it's foam like, in a can. He tried it on my car and my car was covered in dust but after he sprayed it and wiped it, it came out looking like it's just been washed. He also did it on my headlight and it came out like it's been just polished.

I was going to get a can, but it was like $40 so I didn't end up getting it, but now come to think of it, it might have been handy. But they said they didn't have a website, store or anything, they only sell em on locations.

So I'm just wondering if anyone know a good brand.

It looks kinda like this can on the left:

ultraion.jpg

Link to comment
https://www.sau.com.au/forums/topic/328869-waterless-car-wash-spray/
Share on other sites

if you wipe your car with a damp cloth and it will look like it's just been washed too. there are plenty of these type of products at auto stores.

personally i prefer the wet wash because at least then you can hose off the big dirt so that you don't rub it into/against your paint.

Hey guys,

I went to a shopping centre today and there was like a promotion stand with people demonstrating a waterless car wash spray, it's foam like, in a can. He tried it on my car and my car was covered in dust but after he sprayed it and wiped it, it came out looking like it's just been washed. He also did it on my headlight and it came out like it's been just polished.

I was going to get a can, but it was like $40 so I didn't end up getting it, but now come to think of it, it might have been handy. But they said they didn't have a website, store or anything, they only sell em on locations.

So I'm just wondering if anyone know a good brand.

It looks kinda like this can on the left:

ultraion.jpg

Close friend is a detailer, lost count of how many "corrections" hes been doing to paint jobs care of these products. This ranges from the cheap products right up to the more expensive type like dri wash n guard. Best thing to do is your good old fashioned wash, use good quality microfiber mitt to wash and good quality chamois to dry.

Edited by TUFF_350

If your going to use waterless wash.... Use a microfibre cloth on it, a proper one would be best.

They do work pretty good but dont just use any old rag cause it will drag the dirt along the paint. microfibre (Proper) cloth or nothing

I actually just found out the brand and they did have a website :D

The brand is FW1. After doing some quick research, many people say it's bad for the paint and it eats away the clear coat.

But I was thinking to buy it for windows, headlights and rims, is that a good idea? Because it actually did a really good job on my window and headlights

I actually just found out the brand and they did have a website :D

The brand is FW1. After doing some quick research, many people say it's bad for the paint and it eats away the clear coat.

But I was thinking to buy it for windows, headlights and rims, is that a good idea? Because it actually did a really good job on my window and headlights

windows would be alright, but if u got clear on ur wheels, not good, and might not be good for plastics (headlights) if it already eats at clear, plastic might not have a chance!

I actually just found out the brand and they did have a website :whistling:

The brand is FW1. After doing some quick research, many people say it's bad for the paint and it eats away the clear coat.

But I was thinking to buy it for windows, headlights and rims, is that a good idea? Because it actually did a really good job on my window and headlights

yeah i got some, i talked hom down got 4 cans for 100$, just offer them 2 for 50$ they'll do it..Whatever you do dont pay 40$ for a can...Plus you get a 30$ water saver rebate, so 4 cans for 70$and it will last u ages

Ive been using it for well over a year without a problem,.My skyline has new paint and the missus has a new accord with metallic paint, i wash everything with it windows ,wheels, lights, chrome

I usually give the car a quik hose at the carwash 1$ to remove lumpy dirt...Then use the FW1 with a microcloth to handwash it, good thing is it gets waxed at the same time , One can lasted me easily 6 months or more on 2 cars...Id wash them about once a month or so ,so its pretty good value,i still have over 2 cans left . Though i still give a proper carnuba wax once a year or so..

Dont spray it on too thick and wax on wax off with seperate rags and its great stuff for regular washing..have even used it to wash the shower screens amongst other stuff..

So yeah i would recommend it ,but not at 40$ a can :teehee: And i wouldnt wash a dirty car just with that, cause your basically rubbing the dirt of which is what will eat at the clear i reckon not the product itself. Like with most new products people that dont know how to use them properly stuff things up then blame the product itself, Thats my theory anyway, if the clear coat falls of my car I'll eat my words..But our honda isnt garaged,I havent washed it for at least 2 months or more and right now its sitting out in the rain beading like a champion :banana:

Edited by Arthur T3
yeah i got some, i talked hom down got 4 cans for 100$, just offer them 2 for 50$ they'll do it..Whatever you do dont pay 40$ for a can...Plus you get a 30$ water saver rebate, so 4 cans for 70$and it will last u ages

Ive been using it for well over a year without a problem,.My skyline has new paint and the missus has a new accord with metallic paint, i wash everything with it windows ,wheels, lights, chrome

I usually give the car a quik hose at the carwash 1$ to remove lumpy dirt...Then use the FW1 with a microcloth to handwash it, good thing is it gets waxed at the same time , One can lasted me easily 6 months or more on 2 cars...Id wash them about once a month or so ,so its pretty good value,i still have over 2 cans left . Though i still give a proper carnuba wax once a year or so..

Dont spray it on too thick and wax on wax off with seperate rags and its great stuff for regular washing..have even used it to wash the shower screens amongst other stuff..

So yeah i would recommend it ,but not at 40$ a can :whistling: And i wouldnt wash a dirty car just with that, cause your basically rubbing the dirt of which is what will eat at the clear i reckon not the product itself. Like with most new products people that dont know how to use them properly stuff things up then blame the product itself, Thats my theory anyway, if the clear coat falls of my car I'll eat my words..But our honda isnt garaged,I havent washed it for at least 2 months or more and right now its sitting out in the rain beading like a champion :teehee:

That's good to hear. I actually found a sell that'd sell me 2 cans for $40. So I'm gonna try this stuff out.

But I'll probably use it mainly on my windows lol. Does this stuff prevents fog or mist building up on the windows?

Got a better deal than me... :whistling:

It did stop fogging a little but not for long i wouldnt rely on it...Like i said we used it on the shower it didnt stop fogging really..

I usually use rainex or similar product on the windows, outside anyway..awesome stuff..

Cause the honda doesnt get the carport (its reserved for my skyline of course..) Plus we live near the coast i like to wax it good..Just give your car a good proper polish with good quality polish..then use a light coat of FW1 once a month or so to top it up..That way your only waxing over the top of the good wax so i dont see how it could afffect your clear coat really..

But yeah dont wash your whole car with it..the rag gets dirty very quickly and then you are just rubbing dirt back into it, unless you use heaps of rags..But if its well waxed a quick hose will get the dirt off easily, works great for stopping brake dust too..

I use it on all the door/window rubbers as well and they havent dried out or anything..In fact there nice n shiny

  • 1 month later...

I've been using FW1 for over a year now, no scratching, peeling or problems with the paint. Always comes up niice on windows, rims and any exterior surface of the car and restores headlights to clear/see through (removes that mist look). Just be sure to rinse the car before tho otherwise when u wipe the car, small bits of dirt will scratch your paintwork.

It is expensive, but does the job.

I love how it says in the directions for use of the 'waterless' thing:

DIRECTIONS FOR USE:

•Shake can vigorously (5-10 seconds).

•Use in a shaded area (away from direct sunlight)

•Rinse off EXCESS dirt/mud (You don't rub MUD on your car do you?).

•Spray on a light coat of FW1 on a small section (3 or 4 sq. ft).

•Using a terry cloth towel GENTLY rub FW1 in a circular motion (Work smart not hard).

•Allow 10-20 sec for FW1 to dry to a haze.

•Using a second soft towel (we recommend using micro fiber towels) LIGHTLY BUFF TO A SHOW CAR SHINE

Edited by Mayuri Krab

Charles, noooooooooooooooooooooooooooooooooooooooooooooooooooooooo

please, dispose of all FW1 cans (recycle if possible) - that stuff is the work of the devil.

enjoy your plastics/exterior trim whilst you still have it, same for your clear as well..

to everyone else using it, it's some of the harshest crap you could use on a car. for the love of everything skyline, please stop using it!

there's no real need for a waterless system anyway - put a bucket in your shower and collect the water as it heats up, you'll have plenty for even weekly washes.

Charles, noooooooooooooooooooooooooooooooooooooooooooooooooooooooo

please, dispose of all FW1 cans (recycle if possible) - that stuff is the work of the devil.

enjoy your plastics/exterior trim whilst you still have it, same for your clear as well..

to everyone else using it, it's some of the harshest crap you could use on a car. for the love of everything skyline, please stop using it!

there's no real need for a waterless system anyway - put a bucket in your shower and collect the water as it heats up, you'll have plenty for even weekly washes.

Or goto Final Inspection, as you tell everyone in your posts on SAU :)

another +1 for please stay away from this kind of stuff.

Just think about it. You have dirt on your car, you then spray this stuff on and RUB THE DIRT off!!!

Are you farken kidding me! Might as well was your car the normal way, and just run your chamois through a pile of gravel before you wipe the car down. - Same end result.

If you do rinse the excess dirt off, then please explain to me what you are paying these farkers for?

If you do rinse the excess dirt off, then please explain to me what you are paying these farkers for?

It even says to rinse the car off first in their directions for use guide (see my previous post) LOL

But it didn't specify what to rinse the car with so I guess the "water-less" statement from the marketing department is still correct, since you could rinse your car with coke, beer or urine... :ermm:

i wash my car with a bucket of soapy water then F1 it..but you all making me feel bad....

maybe i should change my ways.. :ermm:

I never used it so I don't know whether they are as bad for your paint as claimed on here, so I'm not going to comment on that.

But I like to point out that if you are using the so called "waterless" wash with soapy water then doesn't that kinda defeat the purpose of it being "waterless"?

You might as well just get a standard 2 in 1 wash & wax from your local auto store & just use that (or just use a standard car wash then spray wax) and you will probably save money too...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...