Jump to content
SAU Community

Recommended Posts

Full Car mods are :

ARE front mount intercooler with HPC coated pipes

GCG high Flow turbo ( Garrett 3076 turbine & compressor wheel, shortened heavy duty Actuator arm ) from GCG Sydney

Profec-b boost controller

Apexi Turbo timer

Auto meter boost / Vacuum Gauge

Auto meter oil pressure Gauge

Apexi SAFCII

Spal electric themo fan

3" exhaust System with stainless Cannon Muffler

Pod filter

Cold air induction kit feed from front bar

Blow off Valve

NPC custom Metal button clutch

Gates racing timing belt

Nismo short shifter

front and rear strut brace

Splitfire Coil packs

Body kit;

400r front bar

400r side skirts

Nismo wrap around bumper

black mesh inserts

wheels

18" Degeo customised polished alloy with black centre and Centre of spokes

car currently makes 276rwkw at 15 psi boost turbo capable of 18 to 20 psi but need bigger injectors & full pump

jesus...

so stock fuel pump, AFM, injectors and a piggyback computer?

I'd love to see the AFR's on that thing

i'd be looking into a Z32, nistune/PFC/vipec/haltech, 700cc injectors and an 044 minimum... ASAP

Long time dormant member, this is my current land boat (quite nimble for its size though)

1017668_483118928438226_588193866_n.jpg

Looking to get into another Skyline in the next few months though :)

Previous sled is in the sig below, miss it :(

attachicon.gifDSC_0080.JPG

This my R33 GTST

Hey I'm from here aswell, give me a wave/dose if you ever see me around, I know I've seen this thing around a bunch of times

Edited by G0DZLR

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Good to hear. Hopefully you're happy enough not to notice when driving and just enjoy yourself.
    • I mean, most of us just love cars. Doesnt necessarily have to be a skyline.
    • Did you pick up a manual cluster to remove the position indicator?  (Pretty sure the 34 has the gear position in the cluster, but it's been a while)
    • Here is a recipe. Sonic blocks till you get one that has a good enough bore. Get a torque plate and block brace, use your choice of fasteners (arp ect) bolt the thing together empty, half fill it and let it cure. Release it when it has, go to a REPUTABLE RB Builder and get the thing line bored/honed and cylinder honed to size, then wash. Once its all clean and dandy, wash and blow it out again. Then again.  Assemble said engine to your desired clearances with oil control mods, gasket to suit desired CR/Squish ect. Attach your extended sump with proper trap door oil baffles and head drain plumbed to sump with a SUMP BREATHER SYSTEM. Build your front diff with a decent LSD, rebuild your transfer case with a few extra plates, more than likely replace your tailshaft centre bearing and tighten up the rear diff. Tune to minimise excessive midrange cylinder pressure (timing unless you like to split bores and rebuild engines) Enjoy your engine, but hate the fact you are now destroying engine mounts, gearboxes, gearbox mounts, diff output flanges and driveshafts, diff mounts, tailshafts and front CV's.   Disclaimer.... Ive never done any of the aforementioned stuff.......
    • 440s will support well over 400HP on petrol, which is a decent place to be for an RB20. 230+rwkW. Will be a safer bet for idle/low load. 550s would be nice for the extra headroom. I've made the same decision with mine (Neo25). 1000s are probably too big for the Nistuned ECU, so I have some smaller ones.
×
×
  • Create New...