Best Price For Wideband O2 Sensor In Australia

[chuckie]

G`day Looking to find BEST PRICE ON a WIDEBAND o2 sensor in Australia ,looking for LC-1 which is INNOVATE motorsport type set up.

I looked at few site`s & just wondered who has best PRIECS Australia WIDE,

Cheer`s Chuckie.

[The Dan]

That should rate highly in google search with the capitals

[R31Nismoid]

[Dose Pipe Sutututu]

get it on eBay man, I bought mine off eBay for like $250 delivered for the LC-1 and D/B gauge.

[chuckie]

Cheer`s Man will have a look ,

YES DID GOOGLE ,

[STATUS]

ebay im paying around $98 for innovate sensors (innovate lm1 and lc1)

even for the new MOtec setup on my dyno my sensors are $110

i was using INNOVATE but it is unreliable and slow, as most are well aware.

All Genuine Bosch in Bosch boxes.

[PM-R33]

Techedge 2J2; sensor plus controller $300ish delivered.

Do you need just a replacement sensor? Or a full setup?

[scotty nm35]

ebay im paying around $98 for innovate sensors (innovate lm1 and lc1)

even for the new MOtec setup on my dyno my sensors are $110

i was using INNOVATE but it is unreliable and slow, as most are well aware.

All Genuine Bosch in Bosch boxes.

When you say slow Trent, what do you mean?

I haven't had any issue with my LC1 mounted in the dump, perhaps its the lack of soot with the e85? You do give yours a hard time too.

[Dose Pipe Sutututu]

I remember there was review in some magazine they tested a bunch of simple Wide band O2s and the Innovate had the fastest response time when against Techedge, AEM, and a few other brands.

[STATUS]

I remember there was review in some magazine they tested a bunch of simple Wide band O2s and the Innovate had the fastest response time when against Techedge, AEM, and a few other brands.

not sure how that happens, the innovate has been pretty poor in other comparison's... especially in the trade. Warranty issues since they sold out to another company have been through the roof.

[Dose Pipe Sutututu]

as attached.. each to their own.. I just wend Innovate LC-1 because of it's dual output and because it is recommended on many forums

FordMuscle.pdf

[JonnoHR31]

i had to get a new lc-1 under warranty and its died again now, they replaced it straight away the first time so there was no doubt it was a manafacturer fault.

anyway i purchased myne through this guy, was very helpful and returned it for me to get fixed under warranty.

http://stores.ebay.com.au/superior-auto-pa...634Q2ec0Q2em322

[STATUS]

as attached.. each to their own.. I just wend Innovate LC-1 because of it's dual output and because it is recommended on many forums

FordMuscle.pdf

yeah its an 07 test, i used to swear by their gear used to use LC1's by the truck load in car installs (permanent). I even reckon if you search innovate it will come up with lots of praise from myself, but over the past 2 years it has become a joke.

DOA's and lc1's which wont connect etc.... even my dyno ran a few lc1's for v6 and v8 cars etc but the constant issues drove me nuts, i splashed on the MOTEC gear and it is chalk and cheese, never have i made a wiser choice the things it picks up over the LC1 is phenomenal.

I still have 2 LC1's which are backups and a Trust LM-1 (version one in black) the lm1 is 4-6 years old from memory and is a sweet unit just clunky and proof they used to make good gear as it never plays up.

[STATUS]

BTW this guys is the shit for all tuner tools, great guy. Tell him we sent you.

Half the price of local gear.

http://tunertools.com/proddetail.asp?prod=IN-3744

[DVS JEZ]

i recently bought a innovate LC 1 and XD16 gauge.

had some trouble getting it to work, it was my battery causing this,

after a new battery it was much better,

ive had a few issues with it getting stuck on the heat up phase,

ive had to remove it and recalibrate it 3 times in 3 weeks,

the LOGWORKS program that comes with it wont load has a missing mts error, said to reinstall it so i did, still wont work still has mts error.

i have connected the anologue outputs into my datalogit for a wideband reading on my laptop while tuning. i have tried alot of different configurations to get it reading the same as the XD16 gauge(digital) i can get it even at idle but when under load the guage reads richer than the datalogit,

other than that the innovate is good

makes me worry that the readings im getting are actually correct,

[TiTAN]

http://wbo2.com/home/default.htm

they arent hugely expensive, they are a local product and they work well.

[JonnoHR31]

i recently bought a innovate LC 1 and XD16 gauge.

had some trouble getting it to work, it was my battery causing this,

after a new battery it was much better,

ive had a few issues with it getting stuck on the heat up phase,

ive had to remove it and recalibrate it 3 times in 3 weeks,

the LOGWORKS program that comes with it wont load has a missing mts error, said to reinstall it so i did, still wont work still has mts error.

i have connected the anologue outputs into my datalogit for a wideband reading on my laptop while tuning. i have tried alot of different configurations to get it reading the same as the XD16 gauge(digital) i can get it even at idle but when under load the guage reads richer than the datalogit,

other than that the innovate is good

makes me worry that the readings im getting are actually correct,

i had similar problems, tried shitloads of different earths, read that you have to wire the ground to an2 and set it to delta an1-2. i tried this and the readings were different, in the end i found it closest to correct when i wired it up this way but switched off the delta an1-2. also had to use a seperate ground for a couple of wires i think, cant really remember. fkn weird shit

[DVS JEZ]

i had similar problems, tried shitloads of different earths, read that you have to wire the ground to an2 and set it to delta an1-2. i tried this and the readings were different, in the end i found it closest to correct when i wired it up this way but switched off the delta an1-2. also had to use a seperate ground for a couple of wires i think, cant really remember. fkn weird shit

yeh i tried the delta an1 - an2, doesnt seem to work for me, so i just use an1 and have tried to calibrate it to read the same as the gauge, but under WOT it doesnt seem to be the same,

i have tried different earths but the instructions and their website say u must try to connect all earths to one lug, even the signal and heater grounds together.

i have it working now with the gauge but every now and then it freaks out and i have to jack the car up take the 02 sensor out and do a free air calibration then refit.

[Bliksem]

Anyone tried the PLX o2 sensors?

[Moodles2]

The PDF i read linked here, says the PLX uses the Bosch LSU4 sensor like the other kits do.