Jump to content
SAU Community

Recommended Posts

i been looking around , and cant find much info . i have access to some TOMEI PROCAM 252 degrees duration, 9.15mm lift.

ok from my understanding i will get boost a lil earlier , BUT move my power band up more? how much earlier ? and how much is my power band going to move?

my 26 has got forgied pistons but std rods and crank , and no crank collar with a n1 oil pump , so i not a big fan of reving the shit out of it .

of crouse has a pfc , injectors , etc

so what i am asking is it worth putting the cams in? i usually only rev to about 7,500. the cars used for street + drag.

thanks for any info

Link to comment
https://www.sau.com.au/forums/topic/340229-t04z-no-cam-vs-cams/
Share on other sites

If you are only revving to 7500rpm, the T04Z really isn't the best turbo choice mate. It'll be making power to 8k without a problem... Given it's a 440rwkw odd turbo.

A GT35 would be better and would move the power band to the lower RPM in much better fashion.

Also it wouldn't require as many rev's or risk the pump given the small drive.

That said and you are determined to keep that turbo for whatever reason... Was there any head work done as part of the rebuild?

i had the same problem using a t04z with a std capacity engine. it use to spool at 4 and pull hard till the limiter at 8.

ive changed the exhaust manifold and wastegate made bout 500rpm diferance.

im changeing the cams and gears to 264 as i dont have any head work either and am expecting about about another 300rpm response. so all in all im hoping to get the spool at about 3 and pull hard till 8.

ill keep you posted,

ps there are many guys i know that have cams and a good tune and they get 20 psi at 4000 rpm.

so it is possible.

but like they said T04z LOVES THE ERBS

its a .8 housing .

and why i was asking about cams is my mate just took a set out of his gtr and don't really want too waste money on this motor as i am building another one, so this one will be taken out of car and sold soonish.

E85 will not bring it on any faster will it?

thanks

depends on the housing you have. i have a t04z and it noses over at about 7650 and by 8 its dropping off fairly quick. difference i have cams/gears head work a 2.8lt bottom end blah blah. cam gear would defo help u can set it to come on earlier. and rev it to 8 it will be fine just dont bounce of the limiter. a mate of mine here has a standard gtr engine with just a set of cams gear and 2540's and revs it to 9 all day. once again just dont bounce it off the limter.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • sold listed as a Tomei LSD 1.5 Way For 1998+ Nissan Skyline ER34 25GT RB25DE w/Open R200 https://www.ebay.com/itm/174006114594?campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=&mkrid=711-53200-19255-0&loc_physical_ms=108689&loc_interest_ms=&campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=71883f2ccc571356e0a757bc7adfdde2&mkrid=710-53481-19255-0&loc_physical_ms=108689&loc_interest_ms= it went in like butter all gears, alignment, back lash etc, rotation and clearances correct, and if rolling all rotates smooth and free when coasting down road , clutch in or out over 10 mph smooth... its the binding, clunking and jerking from a stop that is most concerning, also seems like its going to tear the tires off in 10 miles of normal road driving. 
    • What 1.5 way? There's no such thing really as a 1.5 way, just different ways of explaining 2 ways with different ramp rates. HOWEVER. In any driving in a straight line your 1.5 or 2 or 1.7 way should have no clunking at all. With the clutch fully depressed the diff should be silent (unless it's welded but I'm assuming it's not). Something aint right here.
    • Clutch is a spec brand, new clutch system,( PP, flywheel, friction disc, etc. pull type) installed 100 miles ago, with no problems.
    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
×
×
  • Create New...