Jump to content
SAU Community

Recommended Posts

lol the left side of the map is surge, the right side is when its running too hot.

That plot shows that if you are running 20psi, as long as its not hitting 20psi before 3000rpm and if you dont rev it over 8000rpm you will pretty much be making the most of the turbo.

Chances are that turbo wont be on 20psi by 3000 when using the right size exhaust housing, so its good!

They are not available from an australian distributor yet as garrett australia dont recieve them till January 2011 as far as my knowledge goes.

They are available from US dealers (ATP turbo and realstreetperformance are just 2 that we have found so far)

From this garrett link they keep using the figure 10%:

http://www.turbobygarrett.com/turbobygarre...bochargers.html

So I would say roughly 10% more than what they do now.

old 3076 is rated to 525hp atm, used to be 550hp from memory. new gtx3076 is rated at 640hp which is a 22% increase. seams a little optimistic to me using the same turbine housings but time will tell.

old gt3582 is rated to 600hp, new gtx3582 is rated to 750, 25% more.

They are not available from an australian distributor yet as garrett australia dont recieve them till January 2011 as far as my knowledge goes.

They are available from US dealers (ATP turbo and realstreetperformance are just 2 that we have found so far)

Nothing to stop you ordering one from em now ;)

Especially with the dollar in good form

Nothing to stop you ordering one from em now :down:

Especially with the dollar in good form

Sure isnt! Ordering one a GTX3076 for my friends SR next week but ill be waiting till they are here in aus/wa when i buy my gtx35r ;)

old 3076 is rated to 525hp atm, used to be 550hp from memory. new gtx3076 is rated at 640hp which is a 22% increase. seams a little optimistic to me using the same turbine housings but time will tell.

old gt3582 is rated to 600hp, new gtx3582 is rated to 750, 25% more.

Wow so considering i was planning on getting a 3076 and was gonna hit 20psi with 300kw's, so just a guess, but do u think the GTX3076 will be able to hit 350kw's by 20 psi?? Unopened RB25 Neo with supporting mods..

Wow so considering i was planning on getting a 3076 and was gonna hit 20psi with 300kw's, so just a guess, but do u think the GTX3076 will be able to hit 350kw's by 20 psi?? Unopened RB25 Neo with supporting mods..

I'm also interested in knowing how GTX3076 performs on an unopened DET neo, but I'd 350kw by 20 psi is impossible without cams on ULP.

350rwkw is ~ 470whp, how much flywheel hp is it? Let's say 530fwhp. To make this power using PULP you have to force around 55lb/min of air down the engine's throat. 20 psi is 2.43 pressure ratio, plot this poing on the compressor map. I'd say compressor efficiency is still pretty good at ~70% at this point.

At 101% volumetric efficiency you will need ~7400 rpm to achieve this flow, at 95% VE it becomes 7800-7900 region, at 90% VE it's going to be 8300rpm.

So either make sure your VE is adequate at this point (cams, etc), or increase boost or rev engine harder. Or use different fuel, like E85.

And I guess for the new 76mm compressor with all that additional flow, .63 turbine housing will really struggle to flow enough exhaust gasses and will create some serious backpressure in the upper rev range. Looks like at least .82 A/R is an imperative from now on for GTX3076

Edited by Legionnaire
What would be the recommended configuration to get if i wanted to get an internal gate gtx3071, should i go 63, 82, or 1.06, and what dump pipe? Wanting maximum response and 250-275kw :(

If you go internal gate, as a minimum get the garrett IW .82 housing. Preferably see if GCG can supply you with a HKS IW .87

Do NOT go .63, the number of issues to name is annoying. Wont hold boost, problems with heat, choke your motor at any decent boost level bla bla bla.

Better yet would be external gate, but everyone has their price.

GL

old 3076 is rated to 525hp atm, used to be 550hp from memory. new gtx3076 is rated at 640hp which is a 22% increase. seams a little optimistic to me using the same turbine housings but time will tell.

old gt3582 is rated to 600hp, new gtx3582 is rated to 750, 25% more.

Wow they are huge increases!

It's going to be interesting to see how these things match up to "typical" installs using the old-spec GT series turbos.

With the increased compressor flow comes the need for increased turbine flow and maybe a touch less low end response. I'm left thinking the bigger 1.06 housings will become more of a common selection depending on engine and turbo combination.

Just taking time to digest it all.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
    • Wife and I are still looking for a new home. One condition was a large enough garage for a full-size lift in one bay. Now if only we could find something... We've been looking for almost a year now.
    • Thanks everyone for the ideas! Sadly, ramps are a no go for me. With young kids at home, I do most of my work late at night while they're sleeping. Starting the car multiple times wouldn't be a great idea.  I'll go see one of those new long reach low profile jacks and take a couple measurements to see if they will fit.   
×
×
  • Create New...