Jump to content
SAU Community

Recommended Posts

med_gallery_709_1130_37946.jpg

Ok there has been some talk in the locker rooms over the past week. Some of you might have been involved, some of you might have heard rumours, and some might just be in the dark…

Either way, it looks as if we have agreed in principle that it’s about time we held an event to eclipse all those before it.

What better than SAU Nationals right? It’s certainly long overdue, that much is certain ;)

Facebook Group

Username: Skylines Australia Nationals

http://www.facebook.com/settings/?tab=privacy#!/profile.php?id=100002163814442

The rough details are as follows:

Where: Shepparton, Victoria - Incorporating in Winton Raceway

When: 28/29/30th October

Whats going to happen?

Whats going to happen?

- Trackday

- Show’n’Shine

- Burnout Comp

- Some big signature workshop cars

Prizes:

Prizes now around $4500 now, with more to come

$550 in Shell fuel vouchers

$500 in Castrol Oil products (also 100 merch packs to give away)

$1000 in Yokohama vouchers

$1000 in NPC Clutch vouchers

$1200+ - FULL Xforce exhaust system (turbo back)

Also 4 Hot Laps up for grabs in Mercury R35 & Willall R35

Willall R35 looks like it might be getting a big motor upgrade too before the event too!

Most people might need a day or two off work… I think it’ll be well worth it however ;)

If you are a SAU Club member (QLD/VIC/NSW/SA/WA) then you will get priority entry into the events, also heavily discounted entry and accommodation pricing.

Thanks

-Ash

President SAU-Vic

SAU Admin

  • Like 3
Link to comment
https://www.sau.com.au/forums/topic/346683-import-monster-sau-nationals-2011/
Share on other sites

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
×
×
  • Create New...