Jump to content
SAU Community

Recommended Posts

Do we have any results here from this turbo? http://www.ebay.com....#ht_2463wt_1139

Same wheels and covers as all the T67-25g results... Only difference being the anti-surge cover (which may or may not make any difference) and the size of the shaft which should make no difference.

Ratio works as follows as we work back from the large engine will small turbo scenario.

48psi in exh manifold and only 10psi in inlet manifold works out to a ratio of 4.8:1 in theory if we were to try and get the same 48psi of back pressure in the exhaust manifold on the 2l we would need to have 32psi on the intake based on the 1.5:1 ratio (derived from testing).

ahh ok now I get ya, I was reading it wrong.. :thumbsup:

Same wheels and covers as all the T67-25g results... Only difference being the anti-surge cover (which may or may not make any difference) and the size of the shaft which should make no difference.

thats not what she said :P

I don't think it will make anymore power than it did before..

Possibly spool a little earlier and feel better/faster through the midrange though.How's your compression, holding up alright, have u gone new valve springs as well as cams?

Lies 600hp or bust! :yes:

If it went another 10-20hp up top and 20-30 through midrange I'll be happy... Hoping that 20psi will be similar to my old high boost without cams.

No valve springs, mine have been fine up till now.

Compression tests are for nancies :whistling:

Edited by SimonR32

I went to run cams without the valve springs but a few people scared me out of it without horror stories :/

Mine were fitted up this week with the springs and will be tuned possibly Monday, Good luck with yours!!! Hope the cams do make that sort of improvement!!!

The kando should be similar to 3076 yeah? I think thats what i read in your thread?

566hp at 1.7 bar (422kw) without correction

515hp at 1.3 bar (384kw) without correction

So it made an extra 40hp and we didn't even push it as hard, comes on about 350rpm sooner as well. I'll post up graphs tomorrow at work :)

also 590hp at 1.7 bar (440kw) with correction LOL

Edited by SimonR32

566hp at 1.7 bar (422kw) without correction

515hp at 1.3 bar (384kw) without correction

So it made an extra 40hp and we didn't even push it as hard, comes on about 350rpm sooner as well. I'll post up graphs tomorrow at work :)

also 590hp at 1.7 bar (440kw) with correction LOL

Woah!!! :O

Congrats on the results! Amazing!!!

Lies 600hp or bust! :yes:

If it went another 10-20hp up top and 20-30 through midrange I'll be happy... Hoping that 20psi will be similar to my old high boost without cams.

No valve springs, mine have been fine up till now.

Compression tests are for nancies :whistling:

love how this man thinks! nice power dude, 140mph here u come!

For those who mentioned getting poncams, i used a guy in the US that delivered a set for my NEO for about $625 or something..... So they are certainly great value for money based on the results above..... Not sure what they sell for locally but if anyone wants the details i can go find them :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Dredgggggeeee time; I have recently finally started driving the car. It sat for so long that the fuel tank gave birth to rust sludge and blocked my lift pump sock and one of my walbro 460's and left grime, rust chunks and muck all through the surge tank and system. I decided to commit and pull the trigger on an oem r32 gtr fuel tank and Frenchys twin 460 / sender / surge tank hanger combo and all new larger lines and fittings etc, also boost doc heater hose kit / new heater core and a heap of other bits and shits like wideband sensor installed in the dump and Syltech iacv + lines and all wired and added to current tune. now having lightly driven it a couple times without issue, I can happily report on the hta3076 in its current tune. still no boost control switched on, 20psi gate springs, car makes 22psi at 3200rpm in 6th gear with 30-50% TPS from cruise at 100kmh. Going by the old graph, this means it should be making 300-325whp at the same numbers above. Very very responsive setup under true road driving loads. all that's left for the build is body loom + PDM, finish the remote aircon setup, install carbon fibre parts and go for full tune and 30psi. the 315 rear tyres are now performing like they're 195's, wheel spin in any gear at almost any rpm, whereas my previous setup hooked up in 3rd no issue, albeit Nt01's back then / RB25 5spd vs (new) old date r888r's Z34 6spd now, + obviously all the support upgrades I listed in the quoted post above. car sits at 1-3psi on cruise at 100kmh, expectations totally exceeded and I'm beyond stoked with all this so far. IMG_4848.mov
    • I've also been eyeing their rear axles for my car. I purchased seat mounts from them about 7 years ago and they were hot garbage so I've been a little wary about purchasing them. With that being said, please buy them and get back to us haha. 
    • Can a moderator please move this into the right category.. I've accidently put this into racing build thread 🤦🏽‍♂️
    • Being a manual, we very quickly ordered new R34 gearbox (From Nissan) and remaining parts from Kudos motorsports. Would highly recommend the team there. Ultra helpful and quick to share advice and upgrades. We are in the middle of taking the Auto out (Genuine 94,000/kms) and putting the Manual in this weekend. Part 2 of the build will include likely a Plazaman Intercooler and Plenium, Hks Exhaust with Tomei Dump (ordered).
×
×
  • Create New...