Jump to content
SAU Community

What Have You Done To Your Stagea Lately?

Hanso

By Hanso,
in Four Door Family & Wagoneers

 Share

Recommended Posts

  • Replies 9.3k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

chuckie
chuckie

FITTED 2 NEW BOLTS TO MY Brakes is this a MOD i CAN POST or do i need aprovall from NM#% But i may need to ask if it`s ok to POST hope to POST MORE SOON

chuckie
chuckie

Thanks for all your HELP , I guess owning a NM#% is some sort of gift , i guess with all your imput i will be happy to have a NM#% in the family & may be you will be more helpfully then, but a

chuckie
chuckie

LOOKING AT BUYING NM#% CAN I GET SOME POINTERS ON WHATS SHIT & WHATS NOT got some new bolts for Calipers

Posted Images

Jetwreck Grand Master

Jetwreck

Posted
Posted (edited)

How are you going to make the front line up with the flares better?

Getting the front fibreglassed to match...should work....I want the front wheels behind the guard like it is with the AR-X front.

Edited by Jetwreck
Dunc Mentor

Dunc

Posted
Posted

Getting the front fibreglassed to match...should work....I want the front wheels behind the guard like it is with the AR-X front.

:cheers: Sounds like its gonna look the goods!

The rear seems to fit well over them already - does it line up nicely in person?

iamhe77 Grand Master

iamhe77

Posted
Posted

As much as I'd like to hang shit on you Craig, I really like it.

This makes me sad :(

Could you successfully make the exterior of an ARX look good? If so, how long have you been walking on water? :P

Commsman Veteran

Commsman

Posted
Posted

Replaced my 15psi gauge with a 30psi VDO unit.

Turbo arrive from Hyper***r on Monday - minus a banjo bolt that, unfortunately, needs to go in before bolting it up to the exhaust flange. Another public holiday where I'm not able to make the most of my time & get it back together. Just a little bit frustrated with how the turn around time blew out from 3 working days to 3 weeks (plus Easter). In their defence I heard they are short staffed atm, but the poor communication doesn't help either. Grrr. End rant.

I'm sure it will be worth it when it's installed. Visually the in & out ports are significantly bigger. How that translates to power delivery remains to be seen.

bigkevracer Grand Master

bigkevracer

Posted
Posted

Replaced my 15psi gauge with a 30psi VDO unit.

Turbo arrive from Hyper***r on Monday - minus a banjo bolt that, unfortunately, needs to go in before bolting it up to the exhaust flange. Another public holiday where I'm not able to make the most of my time & get it back together. Just a little bit frustrated with how the turn around time blew out from 3 working days to 3 weeks (plus Easter). In their defence I heard they are short staffed atm, but the poor communication doesn't help either. Grrr. End rant.

I'm sure it will be worth it when it's installed. Visually the in & out ports are significantly bigger. How that translates to power delivery remains to be seen.

Somewhat disappointing Leon, but as you say, hopefully it's worth the wait.

Changing the boost gauge... what boost are you planning on running when it's done?

Commsman Veteran

Commsman

Posted
Posted

Somewhat disappointing Leon, but as you say, hopefully it's worth the wait.

Changing the boost gauge... what boost are you planning on running when it's done?

I hope it's worth it too.

Apparently this high flow becomes 'inefficient' around 20psi. I don't know if that was arrived at by some formula or from experience in the test vehicle. AFAIK the M35 they tested it in was pretty stock (only exhaust & boost controller I think), so maybe it was the intake restriction causing the inefficiency. I've no idea what boost will give the best results. Will have to wait & see (& hit up a dyno for a tune).

In any case I needed a gauge to read higher than 15psi. When my old gauge was first installed it was great as I was only at 13 psi so the resolution was excellent - you could easily see half, or even quarter, psi increments. But as things progressed (running >15 psi) the gauge acted like a boost light - either off or off the scale, lol. Other than light throttle uphill where you could see (say) 4 or 5 psi, it was pretty much useless.

keen to see the boost gauge install im still hangiung to get my car back

You're getting the 'super hi flow' yeah? Very keen to hear how it drives compared to mine (or stock).

Here's my old one. New in same spot but reads to 30. Hard to tell in pic, but it's angled towards driver courtesy of a 50mm conduit joiner cut down. You can see the cut out in the lid needed to close over the gauge. Lid's all hollow so I partially filled with expanda foam then used plasti-bond to give a hard surface & sprayed black. Looks almost OEM.

post-76144-0-35275900-1335359707_thumb.jpg

andy65b Veteran

andy65b

Posted
Posted

Apparently this high flow becomes 'inefficient' around 20psi. I don't know if that was arrived at by some formula or from experience in the test vehicle. AFAIK the M35 they tested it in was pretty stock (only exhaust & boost controller I think), so maybe it was the intake restriction causing the inefficiency. I've no idea what boost will give the best results. Will have to wait & see (& hit up a dyno for a tune).

In any case I needed a gauge to read higher than 15psi. When my old gauge was first installed it was great as I was only at 13 psi so the resolution was excellent - you could easily see half, or even quarter, psi increments. But as things progressed (running >15 psi) the gauge acted like a boost light - either off or off the scale, lol. Other than light throttle uphill where you could see (say) 4 or 5 psi, it was pretty much useless.

On the Sierra Stage One any boost over 19psi seemed to make little difference to the performance.

I tried running it at 12psi for efficiency but I found there was little difference in economy and not as much fun as 19psi.

Good luck getting it together soon.

Cheers

Andy

Commsman Veteran

Commsman

Posted
Posted

Set of these are on their way for the stagea.

Nissan 370z akebonos with 355mm Project Mu rotors.

Is it true you need 19 inch rims to clear these? Been looking at these for a while.... very jealous :)

Commsman Veteran

Commsman

Posted
Posted

On the Sierra Stage One any boost over 19psi seemed to make little difference to the performance.

I tried running it at 12psi for efficiency but I found there was little difference in economy and not as much fun as 19psi.

Good luck getting it together soon.

Cheers

Andy

Thanks Andy. I suspect I will find the same thing re extra boost resulting in only heat, lol.

I have a low boost setting atm which nets good fuel economy (10L/100km) & hoping that remains similar. I'll take the high boost setting to as much as the fuel system can sustain &/or the gains drop off. Guessing about 19 - 20psi will be max.

bigkevracer Grand Master

bigkevracer

Posted
Posted

I hope it's worth it too.

Apparently this high flow becomes 'inefficient' around 20psi. I don't know if that was arrived at by some formula or from experience in the test vehicle. AFAIK the M35 they tested it in was pretty stock (only exhaust & boost controller I think), so maybe it was the intake restriction causing the inefficiency. I've no idea what boost will give the best results. Will have to wait & see (& hit up a dyno for a tune).

In any case I needed a gauge to read higher than 15psi. When my old gauge was first installed it was great as I was only at 13 psi so the resolution was excellent - you could easily see half, or even quarter, psi increments. But as things progressed (running >15 psi) the gauge acted like a boost light - either off or off the scale, lol. Other than light throttle uphill where you could see (say) 4 or 5 psi, it was pretty much useless.

You're getting the 'super hi flow' yeah? Very keen to hear how it drives compared to mine (or stock).

Here's my old one. New in same spot but reads to 30. Hard to tell in pic, but it's angled towards driver courtesy of a 50mm conduit joiner cut down. You can see the cut out in the lid needed to close over the gauge. Lid's all hollow so I partially filled with expanda foam then used plasti-bond to give a hard surface & sprayed black. Looks almost OEM.

post-76144-0-35275900-1335359707_thumb.jpg

Nice placement Leon, that's where I was hoping to fit the wideband. Have you got some better close up pics?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • DraftySquash
      Looking for someone with a R34 front bar

      By DraftySquash · Posted

      Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Dose Pipe Sutututu
      new 1.5 LSD issues/concerns

      By Dose Pipe Sutututu · Posted

      Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
×
×
  • Create New...