Jump to content
SAU Community

Recommended Posts

Yeah I'll look at getting it done when I get back to Darwin! Wheel alignment is made such a huge differences also This afternoon put the new filter in and bolted up the front pipe (still standard from cat back) It's amazing! Throttle response is up! Standard boost gauge is now reading 7 (is this Okies) definately gonna try to make back to willowbank next Wednesday! Also managed to lock my 1 1/2 yeah old daughter in the car :( stupid auto locking! She didn't mind, got in after a little bit! Need to get a second key cut

Haha, thanks mate.

I'll be a bit disappointed when this is done as I'll have nothing to to rib you about, lol.

Oh, I don't know; I could always revise my stance on paint colour in the meantime... :whistling:

Had my varex muffler installed yesterday along with dump pipe back 3 inch 100cell cat. When open fark these things are loud compaired to my old 2jz gte aristo.

. Was it worth the wait, how quiet is it closed.?

haha can you post up a DIY with instructions for others with that issue?

I removed the faded and cracked rain shield/wind deflector thingies. Unfortunately the weather strips under won't clean up OK, I think I'll need to replace them sometime.

haha can you post up a DIY with instructions for others with that issue?

1) Go out in wet weather.

2) Wait for dodgy driver to follow closely behind

3) Brake suddenly & get rear ended

4) Boot latch now works*

* Individual results may vary.

1) Go out in wet weather.

2) Wait for dodgy driver to follow closely behind

3) Brake suddenly & get rear ended

4) Boot latch now works*

* Individual results may vary.

Hahaha

Haha I was waiting at a intersection, lady behind thought there was a gap I should of gone for but didnt see the Ute coming. So she went thinking I was going to take a gap, but ended pushing the lower left bumper in a little.

Dont know how but im happy the boot works.

Finally got time to do the exhaust, cust 3" from the cat back, will be doing the dump and front pipe eventually. Also put on an apexi pod filter, dam that thing is loud.

1) Go out in wet weather.

2) Wait for dodgy driver to follow closely behind

3) Brake suddenly & get rear ended

4) Boot latch now works*

* Individual results may vary.

i am intrigued by your ideas & would like to subscribe to your newsletter...

yes very loud. would a mid muffler make it less loud?

Of course, although 'hot dog' mufflers don't do much. You need a 5 inch round body muffler at least, the bigger the better.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...