Jump to content
SAU Community

Recommended Posts

Okies so on the hunt for a boost gauge in the sunny coast Brisbane area before drags on Wednesday! Also modded the airbox and pulled out the corner cap so it can suck in more air!

i am intrigued by your ideas & would like to subscribe to your newsletter...

NP, will email you next issue.

Just be careful he doesn't involve you in his product test procedure.

I tested this procedure on my own car (remember the dump truck rolled into me at road works) & my working boot mech continued to work afterwards, so I'm 90% sure my DIY is accurate. However I am looking for a few volunteers to try it, just to rule out any abnomalies.

Is the hdi any good?

I've never really heard anything exceptional about them. They aren't adjustable for ramp rate or duty cycle are they?

i have one in my 260rs and have never had a problem

Personally I like it. Do have the odd boost fluctuation within 0.8 psi I have found. Have dual stage settings with push button selection. Bought it due to my issues with stock boost solanoid that was playing up and this fixed it.

Is the hdi any good?

I've never really heard anything exceptional about them. They aren't adjustable for ramp rate or duty cycle are they?

Got a tune yesterday from one of NZ's top tuners (def the top Nissan tuner) - will post the results when I get a chance to scan the charts - but learned two interesting things:

1. I have (along with a lot of other people) been using and recommending BCPR6 or 7 spark plugs but they are WRONG! I found my last tuner had gapped them down to 0.5mm to try to eliminate misfiring at high revs and boost (7000 @ 1.4 bar). Soichi said I should use PFR7 to fix this problem. If you check the NGK application guide you will find they list BCPR5 for the RB25DE and for the RB25DET they list PFR5G. So I will be getting some PFR7s!!

2. Don't use E10 fuel (in NZ anyway) - it seems the only distributor in NZ ...Gull... say they use "up to" 10% ethanol so for highly tuned engines it is too unstable.

I was under the impression that platinum plugs didn't fair too well with tuner vehicles and tend to not last as long as the equivalent copper.

No direct experience, only reading. I have both in two different cars.

I was under the impression that platinum plugs didn't fair too well with tuner vehicles and tend to not last as long as the equivalent copper.

No direct experience, only reading. I have both in two different cars.

WTF?

LOL!

And by that I mean technical data, not "my car runs awesome on.....xxxx"

What kind of data would impress you? My car ran awesome on BCPR7ES but the previous tuner showed me on the screen of his dyno the misfiring at high revs and boost but apart from gapping down the plugs he didn't suggest a solution.

The tuner I went to on Thursday was Soichi from ST Hytech and if he is not the best Nissan tuner in the country then he certainly is extremely experienced having tuned many of the top GTRs in this country as well as some in South Africa and a few other places - including street cars, drag cars and circuit racers so he has seen the proof on his dyno as well as on the 1/4mile etc. That's good enough for me. I am sure other tuners can get good results with different plugs and ignition systems - that's cars for you.

I don't want to be impressed. I just want something more interesting than "my car runs awesome on...". I'm not doubting your tuner, if you say he is knowledgable, I have not reason to question it. However, ngk themselves say that you effectively throw out the reference table when it comes to modified engines.

I know you have 100k km service intervals for platinum plugs on stock engines, so obviously the longevity is there in tested conditions. However, my thoughs is that when your running something a fair bit more strenuous than stock, the comparatively thin precious metal coating may well disintegrate quickly compared to a thicker copper item. Especially so if your heat range isn't quite right. Then there is the price difference.... $4 to $20-30ea....

The only set of copper plugs I have ever found for the VQ were $14 a plug, same price I pay for Iridiums which last much longer. I could probably go well over 50,000ks on a set of LFR7's if I chose to, but Cihan likes me to change them regularly. If I want 8's the price goes up to $300 a set. (Nismo plugs) If I could get coppers for $4 I would probably be using them, because tight arse.

Currently running 30psi on stock coils without issue. (on e85) Tractor motors have different requirements obviously. ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even with the piston at TDC there was room for it to drop, but I don't think it can drop fully into the cylinder, the problem you have is that you need something pushing against the valve to hold it up so you have enough room to put the new stem seal on and the spring etc.  I used compressed air only because putting rope in the cylinder seemed a bit risky to me, I know people have done it countless times before like this. Overall it's a pain in the ass job. Honestly you'd probably be better off taking the head off because the risk of dropping something in the engine and the finicky-ness of it all is very stressful. If you are going to attempt it though i 10000% recommend a 36050 valve spring/keeper tool. I had both the traditional lever type and after doing 1 cylinder it was absolute pain to get those valve keepers in place, even with 2 people. That 36050 is amazing, you do have to push hard to get them in place but it works perfectly almost every time. Back to my actual issue I think my engine is just tired and old and the rings have gone bad. The comp numbers (cold, no oil) were: Cyl 1 -129psi Cyl 2 - 133psi Cyl 3 - 138psi Cyl 4 - 137psi Cyl 5 - 157psi Cyl 6 - 142psi   Cylinder 5 and 6 having the most carbon on them.
    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
×
×
  • Create New...