Jump to content
SAU Community

Recommended Posts

On 15/6/2022 at 4:11 PM, oxford1327 said:

What does this question mean?

The alternator needs to see some sort of load to start charging. This is typically done with the charge light in the dash. You don’t have this light so where does the alt get a load from

On 6/15/2022 at 4:17 PM, RBW49N said:

The alternator needs to see some sort of load to start charging. This is typically done with the charge light in the dash. You don’t have this light so where does the alt get a load from

Ahhh righto, I've got no idea, when it comes to electrical stuff, me and wires have a toxic relationship,most times I let the smoke out of em.....so I leave that stuff to others.

So I'm guessing that installer has that sorted, but if battery starts to die I'll see if they missed doin that.

well, you'll be able to tell immediately if it is not sorted because you will have 12v and lower when the car is running. If it is 13.8ish all is well.  One option is to add a resistor instead of a battery charge globe which can be hidden behind the dash, but you lose the warning it your alternator isn't working with that solution.

  • 3 weeks later...
  • 1 month later...

Currently designing and testing a 3d printed holder for my Boost Gauge on my RS Stagea. Keen to know if anyone else out there has had a go at 3d printing parts or mods on there cars 

PXL_20220809_015618715.jpg

Screenshot 2022-08-09 122717.png

  • Like 1

Great idea. Once apon a time there were gauge pods available that replaced the stock clock above the dash as well, would be great to see an option for a printed replacement.

How is the visibility to the gauge from the driver's seat?

I looked at the clock replacement made by Mearcat (http://www.mearcat.com.au/stagea.html) but it just looked a bit bulky to me so I decided to make have a go at making my own. While visibility is good I think it is a location better suited for something like a voltage gauge I want to try making a holder to replace the air vent by the drivers door just trying to figure out how to get the damn thing out  

  • 2 weeks later...
  • Duncan pinned this topic
  • 1 month later...

i present to you made from old chopping board a prototype of a cold air intake to match up to the factory airbox on a RB25 Det neo  s2 Stagea 

I'm just using foam just to keep it of the bracketry for the high beam and bonnet latch 

but just from testing the throttle response seams to have improved but cant be sure its just placebo going to drive with it for a while to see  and if I do feel it is worth while I will look into making a more permanent solution 

ps. got the original idea forum this forum post when looking for replacement foam for the air box (http://www.r33gt-r.com/2009/04/breathing-better.html)

PXL_20221017_224229216.jpg

PXL_20221017_224259325.jpg

PXL_20221017_224245372.jpg

PXL_20221017_224305787.jpg

  • Like 1
  • 3 weeks later...
  • 4 months later...

Manually converted about just under a year ago, loved driving it but was ready to chuck in some big boy parts. Started with plazmaman half intake, which made the car terrible to drive. Waited a few months for more gold and then bought hot side parts then got them fitted with fabrication including custom intake, intercooler pipes, washer fluid, power steering, overflow tank and catch can. After that I needed a bunch of lines and a whole fuel system overhaul and fluids for new ball bearing turbo. I decided I might as well upgrade oil cooler, re-located oil filter to a better spot. After all that was done it was time for a haltech plug in play kit with supporting sensors, also have ic7 wiring all done, just need to leave old cluster in to sort out my 4WD light which is still haunting me. Which leaves my next goal which is to sort that out and cert the car. That hopefully shouldn’t take too long because I’m going to build my head next.

  • Like 1

Ooo, sounds pretty good @SLIXK! Do you have any photos?

Also, which oil cooler did you get? And did you go with a kit for oil filter relocation? These two things are on my wishlist for when I have some more funds. Haven't done too much research yet though.

Would also be interested to hear how you go with getting everything certified when you get there.

3 hours ago, soviet_merlin said:

Ooo, sounds pretty good @SLIXK! Do you have any photos?

Also, which oil cooler did you get? And did you go with a kit for oil filter relocation? These two things are on my wishlist for when I have some more funds. Haven't done too much research yet though.

Would also be interested to hear how you go with getting everything certified when you get there.

Setrab oil cooler bro, not sure what relocation kit was used, but filter is right inside the arch of the right wheel behind the plastic.

8BF672C6-7B0B-451B-8020-83B0FB20505F.jpeg
 

I’m also I’m based in New Zealand so not sure if the cert stuff isthe same or not but I will let you know how it goes.

Edited by SLIXK
  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...