Jump to content
SAU Community

Recommended Posts

Wrapping them in heat tape does void the warranty with 6boost. Also when i had mine heat wrapped i had silicon joiner close to manifold like your hard piping, burnt straight through the joiner, i would be looking at modify that piping more or finding something you can wrap the piping in to prevent it burning out.

  • Replies 161
  • Created
  • Last Reply

Top Posters In This Topic

yeah just lay a piece of heat reflective material over the silicone joiner that is close to the mani. that will protect it.

the mani's look very nice mate. hope they give some good gains. I think they will.

like this stuff. pic if of my old GTR set-up. the boys added heaps of the stuff for me to protect hoses etc. I was running HKS turbos on tomei mani's with tomei dumps.

post-3621-0-12896500-1299731109_thumb.jpg

plus you can see even with the tomei manis and dumps the front turbo dump is VERY close to the rear turbo compressor inlet. I used the trust piping kit which is nice as the rear inlet is cast and then also had the dump pipe wrapped to help.

post-3621-0-47453000-1299731193_thumb.jpg

here's the hard pipe kit I used. it's my favourite (have used it and the HKS one like yours) but unfortunately I don't think it would work with your mani's and with the RB30 it would all end up too high.

post-3621-0-69870500-1299731340_thumb.jpg

like this stuff. pic if of my old GTR set-up. the boys added heaps of the stuff for me to protect hoses etc. I was running HKS turbos on tomei mani's with tomei dumps.

post-3621-0-12896500-1299731109_thumb.jpg

plus you can see even with the tomei manis and dumps the front turbo dump is VERY close to the rear turbo compressor inlet. I used the trust piping kit which is nice as the rear inlet is cast and then also had the dump pipe wrapped to help.

post-3621-0-47453000-1299731193_thumb.jpg

here's the hard pipe kit I used. it's my favourite (have used it and the HKS one like yours) but unfortunately I don't think it would work with your mani's and with the RB30 it would all end up too high.

post-3621-0-69870500-1299731340_thumb.jpg

I was using the same manifolds and dumps. Still going with the tomei Dumps.

I plan on using a piece of OEM heat sheild. The multi layer with ceramic internal. Your hard pipe kit definately won't fit. I checked my clearance today and my kit will fit under the bonnet..by a very small margin.

I have heat wrapped the manifolds and prettied them up with some black therma-tec spray. I have to remove the head to reduce the oil restrictor down to 1mm, then will complete the installation.

Matt

Edited by BoostdR
  • 2 weeks later...

prob another week or so guys, depends when my delivery from the States arrives. Was sent on the 20th so hopefully not to far away.

Matt

hoping to fill the mid range in a little. Note this is Flywheel

post-49288-0-99180000-1300934334_thumb.jpg

Edited by BoostdR

My low mount 6boost manifold comes extremely close to the rocker covers and mine are painted in two pack paint and the mani is ceramic coated and i havnt had any issues with the paint so far. Im only running a single 35/40 though. The best thing you will get out of these manifolds is the noise haha! oh and the performance gain of course.

considering he already had sizeable lowmount manifolds (aftermarket) before this, i'd be surprised is there was a major exhaust note alteration.

jury is still out on the performance side as well.

3 pages, we need results :D

Guys,

didn't feel like this warranted starting it's own thread.

250kw GT3076 0.82 with 50mm ext gate welded on to stock manifold... screamer pipe, decat 3" turboback

If I get a 6boost manifold, would that make much difference at all to my setup?

I wouldn't bother at your power level. The OEM manifold is a good thing up to 300rwkw

Its always good to have a read of these type of threads so we can get some real world feedback.

Looking forward to seeing the back to back dyno test results, we don't get to see back to back testing often enough...even for our own liking!

As for the stock manifolds on RB25 being good for up too 300rwkw, while we don't disagree with that comment we have seen GT3076R's spool up to 400rpm sooner on RB25's and make slightly more power also with back to back testing.

Most of our RB25 customers running GT3076R's see upwards of 300rwkw on 18psi. Not sure what your 250rwkw was made on...but it might help :-)

Matt

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...