Jump to content
SAU Community

Recommended Posts

Hey Dale, thanks for the suggestions on extras. Have you posted a pic of your custom mount / air duct? I would like to see what you've come up with.

I think method 2 is the way to go and your reason above makes a lot of sense. Previously I was only considering implications when cold, but of course it is more important to consider what happens when hot since that is the most common state.

Just went out & pulled my grille out; the things I do...whistling.gif

post-61153-0-22466700-1301887419_thumb.jpg post-61153-0-80608700-1301887455_thumb.jpg Doesn't need a top plate as the grille bar is about 5mm away.

and peeking through the Grille;post-61153-0-57769800-1301887505_thumb.jpg

Hope that explains it.

Just went out & pulled my grille out; the things I do...whistling.gif

Hope that explains it.

Well, that was unexpected... I thought you might have had some pics stored away. Thanks for doing that specially for me (us?).:thumbsup:

Setup looks good. I'll store these away for when I do mine.

judging by the pic, it looks like you could fit it in the same spot with the HDI..

confirm?? looks like a good setup Daleo

Yep, it all sits forward of the back edge of the bar reo; so no clearance issues.thumbsup.gif

Well, that was unexpected... I thought you might have had some pics stored away. Thanks for doing that specially for me (us?).:thumbsup:

Setup looks good. I'll store these away for when I do mine.

No worries.

A couple of test launch's that even surprised me.......a lot!!!!!!!!cool.gif.....lag's no issue....traction is though!!whistling.gif

Surprised you!!!????

My Mrs is still refusing to wash those underpants :wacko:

got some turbo studs today...... are the originals nuts M10x1.25 thead ???

thead seems pertty damn close right up untill the last bit...... could that be the locking part biting in ???

got some turbo studs today...... are the originals nuts M10x1.25 thead ???

thead seems pertty damn close right up untill the last bit...... could that be the locking part biting in ???

What did you buy, did you get them from the link above? If so you will need the nuts to suit as they are 1.5mm pitch.

The stock studs are M10x1.5 into the turbo and M10x1.25 for the dump side with the nut.

What did you buy, did you get them from the link above? If so you will need the nuts to suit as they are 1.5mm pitch.

The stock studs are M10x1.5 into the turbo and M10x1.25 for the dump side with the nut.

nope i got some from my exhaust guy there the same as stock so ill reuse the old nuts....... if i can get them off the old studs LOL.

also as a side note: he recommended NOT using stainless steel studs

Did he give a reason? I have had no problems with the stainless studs and copper nuts. Much better than reusing the old nuts imo.

+9..

im using them and no issues.. and looks much cleaner too as the studs are shorter.

nope i got some from my exhaust guy there the same as stock so ill reuse the old nuts....... if i can get them off the old studs LOL.

also as a side note: he recommended NOT using stainless steel studs

Most mechanics shy away from stainless due to the galling and binding issues you get with unlubricated threads and stainless or high tensile nuts.

They also have this odd idea that stainless goes brittle when used on exhausts(which is odd; cos they're happy to fit a stainless manifold or dump pipe); which is also a furphy.

Obviously not an issue when using copper nuts...

SO PISSED OFF the cars not back on the road........ still witing on parts FFS!!!

if only i knew it would be this much hastle i would've payed some poor barstard to do it and save myself the freaken headake!!!!!!!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
    • BTW I measured the jack I have, it is 70mm at the saddle but you only have about 700 until it returns to 150mm high at the cylinder so it is good but no magic bullet.
    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
×
×
  • Create New...