Jump to content
SAU Community

R32 Gtr Oil Pressure

ripps

By ripps,
in Engines & Forced Induction

 Share

Recommended Posts

Beer Baron Grand Master

Beer Baron

Posted
Posted

they are shit. get a proper aftermarket one and you'll be astounded at how fast and by how much pressure changes with RPM. the stock gauges are purposely dampened in their response as nissan (and other companies) thought wildly moving gauges would alarm the general car driving public and people would think there was something seriously wrong with their oil pressure. so what you get is a very slow moving gauge that is no where close to being accurate at any given moment.

Moodles2 Grand Master

Moodles2

Posted
Posted

I'm in the market for a aftermarket oil pressure gauge, should i look for one with a mechanical sender or a electric sender? and is there any cheap gauges that will do the job (and not be flashy expensive like Defi)

Beer Baron Grand Master

Beer Baron

Posted
Posted

electric sender for sure. mechanical is no good, that means having fluid in the cabin and if a line or coupling splits or the gauge fails you'll get a nice spray of 110degree oil in the cabin!

i have to be honest I run defi's in 2 of my cars now and whilst they are expensive I reckon they're worth every penny. but for cheaper options you can probably pick up a used trust guage. they don't require a main controller (each gauge has it's own) and they have peak hold and warning function which is important for a oil pres guage, you want one that tells you when pressure drops low. probably looking at under $150 for something decent. also defi now make gauges that don't need controllers, sort of a budget entry level defi gauge, I'm sure they are quite good too.

Thelen Rising Star

Thelen

Posted
Posted

My R32 GTR pressure gauge doesn't seem to work at all, along with the front wheel torque thing, I am assuming just because of age however something else might be broken.

What is the best way to proceed with getting it diagnosed, then finding a replacement etc? I don't really care about having a bunch of clusters, so just something in the stock position would be fine.

Sloane Experienced

Sloane

Posted
Posted

Anyone know where I could find a 3 Guage Holder to replace the stock one in a BNR32?

As everyone is saying in this thread it seems the factory ones are definately unreliable and to get aftermarket for more accurate reading's.

mico Proficient

mico

Posted
Posted

My R32 GTR pressure gauge doesn't seem to work at all, along with the front wheel torque thing, I am assuming just because of age however something else might be broken.

What is the best way to proceed with getting it diagnosed, then finding a replacement etc? I don't really care about having a bunch of clusters, so just something in the stock position would be fine.

just follow the wires up from the sender and check the connections :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...