Jump to content
SAU Community

Recommended Posts

  • Replies 204
  • Created
  • Last Reply

Top Posters In This Topic

just going through the sup regs and it says that vehicles need to have a dashboard. does my one count as its not a factory thing?

P4220003.jpg

also, how strict are they on the seats? mine has no CAMS/FIS tags on it (Cheapo copy seat)

First update wont be until the end of the week as we have to rely on Renew for this one (their name is on the booking for this one, ours is next after this one)

Paid and sent for off today.

I have entered in street class as most of the day will be done on street tyres. Will it be a problem later on in the day if I change over to some full slicks if I am feeling game? Or does that then change the requirements to needing a harness and a full roll cage? I don't mind if the times don't count. Just entering for a bit of fun with my car.

cheers,

Nathan

Transferred funds and faxed off form today, I will again endeavor to do a sub 1:10, I'm sure the car would do it easy, its the dodgey driver that's holding her back.

Probably the last outing for my current set of semis too, I'll be needing to win lotto to pay for the next set, or I'll buy them from the good old US of A as the dollar is still looking bloody good.

Because it is being run as a super sprint (timing) / track day RENUW have used SOME rules from a standard type of super sprint reg sort of ? ! .

SAU track days will be back to normal after this little comp, and will be more focused on driver training and taking a mate for a spin, as pointed out there are lots of clubs to do sprints and/or door to door style of racing, SAU is more about having fun in a low risk enviroment with mates where you can go as fast as you like (as long as your speed matches your ability).

Still for a small outlay you can have piece of mind that if your car, someone elses car or if your mates hair catches on fire you can put it / him / her out and save your s hit from burning to the ground.

$20 could save so much.

I have 1.5kg in the car, .900kg in the kitchen, 2kg in the garage, you may say overkill, I say my sh it wont burn down.

:cheers:

In car fire extinguisher required?? Seriously??

Is this something that will be more and more prevelant for Track days, or just something special for this one?

Cheers,

They're $50 and could save you from watching your car burn while you're powerless to do anything about it. Ive got one in each of my imports just to be safe, for $50 why would anyone not have one?!

I think you'll find over time more and more days will require this basic safety item but for now as we are running with renew we seem to be one of the first :)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...