Jump to content
SAU Community

Recommended Posts

I will never forget my first car!

I'd like to see yours!

These 'snaps' I dredged up from 1970...

Enjoy!

Chrome wheels were IN.

1600-1.jpg

Pinstripes were IN

1600-2.jpg

Matte black panels were IN

1600-3.jpg

Smiths gauges, new cassette radios, snooker ball gear knobs, leather steering wheel covers were IN

1600-4.jpg

Any hoon had to choose between Weber, Delorto, SU etc and carry the new Lynx manifold home in a bus - lol

And these are the exposed pods you'd not want to smoke a fag nearby - lol

1600-5.jpg

Night-time shot with the state-of-the-art Minolta SRT 101 with Rokkor lens

1600-6.jpg

50mm Rokkor f1.2 big sucker to be exact

1600-7.jpg

Minoltas back then were used by Trent Nathan, son of rajab Snowdon etc. Some photographers used to even scavenge Rokkor lenses to stick on their Nikons.

Believe it or not!

Link to comment
https://www.sau.com.au/forums/topic/367180-your-first-car/
Share on other sites

  • Replies 48
  • Created
  • Last Reply

Top Posters In This Topic

My first car - 1993 R33 GTS. Since I sold it 2.5 years ago, it has since had 4 owners, before finally coming to a rest with a now good friend who's looking after it.

This is how it looked when I sold it:

105686041_b7qqcF31.jpg

Sadly it was crashed yesterday :( Thankfully no one was badly hurt and the car is repairable.

Link to comment
https://www.sau.com.au/forums/topic/367180-your-first-car/#findComment-5856772
Share on other sites

Jeez Terry you just brought back some memories, my first car was a 1969 datto 1600.

1.8 litre rebuilt and bored out to a whopping 1910cc, side draft webber (48mm I think) 240k gearbox which used to confuse all my mates cause reverse is where 1st should be. Stanza seats and a plywood console with a oil AND water temp gauge wow

I remember it had one of those pop up aftermarket sunroofs that use to bucket water onto me when it rained.

Dunno if I have any photos I'll have to have a look.

Man I loved that car, coincidentally it's was the same colour as my current 33. Jeez I got up to no good in that thing on the dirt roads.

I lost something on the back seat that I'll never find again ;) Good times

Link to comment
https://www.sau.com.au/forums/topic/367180-your-first-car/#findComment-5857280
Share on other sites

  • 2 weeks later...

21561_104937912865442_100000477008080_133181_1649311_n.jpg?t=1307869394

First old 202 red 5speed loved the dirt

14457_100416149984285_100000477008080_7396_19308_n.jpg?t=1307869458

14457_100477523311481_100000477008080_9321_6077234_n.jpg?t=1307869394

PC180004.jpgHX 1 tonner 308 :D

sold it shouldnt have :( but brought my falcon and the turbo bug hit big time

14457_100416156650951_100000477008080_7398_3493269_n.jpg?t=1307869459

Then 04 xr6T capa flash . valve springs and supporting mods 10psi ( harder 2 get parts 4 ) so i went SKYLINE!!

Link to comment
https://www.sau.com.au/forums/topic/367180-your-first-car/#findComment-5882941
Share on other sites

4b67c9d6f36913c29b6fa4cf6.jpeg

not a picture of mine but splitting image nonetheless

learnt to drive manual in the trusty ol' family workhorse corolla, 1989 model so just two years younger than me, sold it only a few months ago. was really like a part of the family since we had it so long :thumbsup:

Link to comment
https://www.sau.com.au/forums/topic/367180-your-first-car/#findComment-5883465
Share on other sites

First car, at least it had an RB

DSC02147.jpg

Put a rebuilt engine in with a slightly bigger then stock Cam, Painted engine bay + Engine. Was nice, fairly proud of it, but the Skyline is nicer to drive, faster, more reliable and looks alot better

DSC02051.jpg

Link to comment
https://www.sau.com.au/forums/topic/367180-your-first-car/#findComment-5894078
Share on other sites

First car, at least it had an RB

Put a rebuilt engine in with a slightly bigger then stock Cam, Painted engine bay + Engine. Was nice, fairly proud of it, but the Skyline is nicer to drive, faster, more reliable and looks alot better

Very tidy VL!

Here's mine - a 1989 Prelude 2.0 Si - the first production car with four wheel steering!

5657739942_7a72cba169_z.jpg

Smiths gauges, new cassette radios, snooker ball gear knobs, leather steering wheel covers were IN.

1600-4.jpg

Love the dashtop tacho. Looks a bit like the lap timer / stopwatch on the new Porsches with the Sport Chrono Pack (expensive option):

2010_porsche_911_sport-classic_23.jpg

Edited by God_speed
Link to comment
https://www.sau.com.au/forums/topic/367180-your-first-car/#findComment-5895680
Share on other sites

  • 2 weeks later...

here's mine, 1984 Nissan 300ZX, Z31 NA. Was my pride and joy, spent way to much on it, shopping list went something like, 2 engines, 2 gear boxes, 3 clutches, 2 diffs, to start with. Learnt most of what I know about cars on this machine.

Had a custom jap rubber front bar (came rolled up in a box!), side skirts, shaved off side bump stops and welding over seams to give it a cleaner look, then painted with a Corvette burnt orange. was VERY bright!

Desperately needed to be lowered, but I sold it and picked up my skyline before I did.

5929425387_4954128b13_z.jpg

5929982256_19df4ef8b2_z.jpg

5929425923_5b2824d814_z.jpg

Edited by 33driver
Link to comment
https://www.sau.com.au/forums/topic/367180-your-first-car/#findComment-5910404
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
×
×
  • Create New...