Jump to content
SAU Community

Recommended Posts

6 x Xspurt 1000's and Proflow RB25 rail would be around $800 through me I think Mark, with all adapters.

Scotty - will that rail fit with the stock plenum? We are looking at going to E85 in the next few months, so I am interested in an injector upgrade.

I think so mate, the 1000's might be a tight fit, but the shorty 750's and 2000's are definitely no issue. I may even be able to get 1000's in the same shorter 1/2 length.

The SR20 rail kit I sell comes with a plenum spacer to help the 1000's clear the upper plenum. Perhaps you could do a similar thing to the RB plenum halves using bakelite or a similar insulating material, that way you would stop the heat transfer into the upper plenum also.

What paper filter are you using, I was told to be careful when use paper filter cause the ethanol can/does eat away the "glue" that holds the filter element to the casing

I'm using a speed flow 10 micron stainless sceen filter but the paper ones can go down to 5-6 micron which would be better

I am using twin Proflow stainless mesh filters, I haven't cleaned them in 3-4 years, since they were installed. I can't remember what micron they were...

The paper filters I have been buying were SX brand, suitable for alcohol fuels. (They have a similar 8an housing to the proflow/Speedflow style filters, and might just drop in to them.) I run the SX fuel reg in my car without issues so I knew it was good gear.

A little Googling reveals Arram as a Japanese manufacturer who make injectors, throttle bodies and carburetors.

Yeah, just wasn't much info and didn't know if these were common in rb20's or not.

Most of the stuff says 550cc, so should be all good, cheers. ;)

Hopefully it doesn't cost you too much dyno time to set them up, it can take a while to work out suitable lag times etc with unusual injectors, and you are paying good coin for every minute it's on the dyno.

Unless you have the lag time report with them? Might be worth trying to source one.

Hopefully it doesn't cost you too much dyno time to set them up, it can take a while to work out suitable lag times etc with unusual injectors, and you are paying good coin for every minute it's on the dyno.

Unless you have the lag time report with them? Might be worth trying to source one.

Never knew injectors even came with a "Lag time report" lol..

I was going to get them tested and flowed before I chucked them on anyway. I think they're a little old.. :P

  • 3 weeks later...
  • 4 years later...

To save starting a new thread.....

Is the contents of this thread still relevant?!?!

As in are the ID injectors still worth paying basically twice the price or are the EV1-Bosch items closer to the mark 5 years down the track?

(Looking for 11mm units to suit standard RB26 fuel rail to get me around the 400rwkw mark on E85...)

ID1300x or 1250cc.....?!?

 

 

Edited by mr_rbman

There are better options (than ID specifically) and have been for years.  You should perhaps PM Scotty to find out what he can do for you.

Basically, if you can get unmolested EV14 injectors in the size you need, that is best approach.  But even the ones that have been decapped are pretty good.

5 minutes ago, GTSBoy said:

There are better options (than ID specifically) and have been for years.  You should perhaps PM Scotty to find out what he can do for you.

Basically, if you can get unmolested EV14 injectors in the size you need, that is best approach.  But even the ones that have been decapped are pretty good.

I had tried pming Scotty before posting but either his inbox is full or there's an SAU issue as i just get an error saying he can't receive messages, or something similar....

Cheers for the reply though....

I do have the 1250cc injectors that Kudos sell in my 'cart' but after reading a few threads on here and then googling I was having second thoughts....

Tier 1 - ID 

Tier 2 (½ the price) - Bosch Motorsport

Tier 3 (aka shit and not worth it, also ¼ the price) - Everything else

Genuine Bosch Motorsport '040' injectors with adapters for RB26 manifold would be the go. I'm sure NZEFI sell them as a kit.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...