Jump to content
SAU Community

Recommended Posts

Hey, I want to order a set of TE37's for my R33 GTR but I'm not 100% on which size to get.

I'm looking at either 19x10.5 +12 or +22. My car isn't very low and doesn't have much camber. I don't want to roll my guards either. I would be happy to dial a bit of negative camber in to get the +12's under there though.

Just want to know from peoples experiences if the +12 offset can be done without rolling the guards.

Thanks,

Mike.

Link to comment
https://www.sau.com.au/forums/topic/375570-te37s-for-r33-gtr/
Share on other sites

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

I scrub my drivers inner platic lining with a 19 x 9.5 + 12 running on a 275/30x19 tyre.

What's everyones obsession with 10.5 inch wide rims? a 275 looks a little stretched on there and really looks a bit limp wristed!

Thanks heaps for the replies, definately happy I went with the +12's.

Just need to work out what tyres I'm going to run now.

Thanks,

Mike.

who did you end up ordering them through? looking at getting a set of te37 too...

I ended up getting a set of varrstoen copies. Couldn't justify spending 5k or wheels if I don't even track my car.

Cost me $1600 delivered

Thanks,

Mike

So far, they are probably the best for copied TE37's.

Still 19x10.5 +12?

What colour you get?

I ended up getting a set of varrstoen copies. Couldn't justify spending 5k or wheels if I don't even track my car.

Cost me $1600 delivered

Thanks,

Mike

If you track it, this is probably your best option anyway.

Try buckling or cracking one of those TE37s, it hurts.

Waiting to see fitment pictures of these on the 33.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...