Jump to content
SAU Community

Recommended Posts

I have the best of both worlds then! And no silly stripes to go with it!

nismo_tiida_s_450-op.jpg

By the way- Boost is a steady 0.35BAR, or 5 PSI. I'm not using over 4000rpm, and I'm going to check the stock injector (320cc) duty cycle soon. Stock Computer is dumping a lot of fuel into it, fuel consumption is..... interesting. But over all, its totally drivable at the moment.

By the way- Boost is a steady 0.35BAR, or 5 PSI. I'm not using over 4000rpm, and I'm going to check the stock injector (320cc) duty cycle soon. Stock Computer is dumping a lot of fuel into it, fuel consumption is..... interesting. But over all, its totally drivable at the moment.

Interesting, but don't you mean 370cc?

I'm pretty sure that the VQ35de has the same sized injectors as VQ25det.

From recent testing at APS the stock VQ fuel injector flows 328 cc at 100% duty cycle at 43.5 psi fuel pressure, 376 cc at 100% duty cycle at 58 psi fuel pressure and 412 cc at 100% duty cycle at 72.5 psi fuel pressure.

linky

They wouldn't bother with the ghey market....

HKS is to busy building stuff like this...

HKS R34 GT-R

HKS-BNR34-268.jpg

Wonder where I can get some HKS Stripes...?ninja.gif

Lolz

Is that it?....taxicab chassis for the broz!

What about the gt500 stuff?

hmm... fair enough... quick check of FAST resulted in;

PM35 injector part number is 16600-CD70A and is used in Z33, J31, F50 etc. Basically everything that is running a VQ35de.

NM35 injector part number is 16600-AA500 and is used in F50 (VQ30det), R34 (RB25det) and Y61 (TB48de).

Now to back track and find where I thought/read that they used the same injectors wacko.gif

Trick for new players- do up your trans cooler clamps tight when they are nice and hot! whistling.gif

I played Hansel and Gretel all round Sydney with Matic J yesterday. Anyways, noticed a puddle in the garage this arvo, sorted it out. Thought it was engine oil to start with, glad it wasn't!

Now have a nice layer of underbody rust protection!

Exciting news!

UPREV have patched my ECU. It now appears on the webpage for supported vehicles. I received an email for Mark @ Abbey Motorsports in the UK telling me of the good news. I now have a tunable ECU map, a "back to stock" map.

Now I just have to pay up, refresh my licence arrangements, and I'll be tunable!

tongue.gif

Bit of progress today.

A couple of days ago I re-flashed the ECU. Just with the stock values, but with the throttle restriction removed, Speed limited to 300km/hph34r.gif, and a little adjustment of the rev limit/fuel cut/ throttle cut. All went successfully.

I have been having a problem with the ECU learning some strange fuel settings on closed loop. Basically what was happening was that on closed loop, Bank 2 was running a lot richer than Bank 1. it was about 80%/120% ratio. It didn't occur when the ECU was just fresh, but when it had driven for ~150kms, and the ECU learnt it. At the time it was stock ecu, not re-flashed at all. When it went open loop, it was fine. It spat a U1000 error, which is CAN bus error. Now nothing is wrong with the CAN bus, but what triggers that code, is when the ECU doesn't receive data from the emissions diagnostics for more than 2 seconds. So I went searching today- first port of call the bank 2 wideband sensor. When I pulled it apart it seemed ok, but the little rubber thingo in there wasn't sitting quite right so I pushed it all the way to the bottom, cleaned the plugs out and reconnected it. Also found a nipple in the intake tubes wasn't tight, so tightened that up. Anyways, the problem is absent now, I haven't put that many kms on it yet since the last "clear learned fuel" but I am optimistic that it will stay away. Idle is nice and smooth now, and while there is a little inconsistency,its not much, and doesn't appear when the car is at cruise with light throttle.

I want to know that the problem is gone, before I proceed with 600cc Injectors and fuel pump and tuning, as that would just exasperate the issue.

Also wired up my boost gauge, so now I know wtf is going on at night too!

Thought my exhaust was quiet- so got one of those Apps that measure Db. Don't know how accurate they are, but hey.

Measured according to the testing procedures- Exhaust height, 45 degree angle, 500mm away from tips

Measured 90db @ 4000rpm.

Legal ! banana.gif

Ok, some pics.

Any questions, ask away-

6839443439_41e60411e1.jpg

6839442021_e14db70f61.jpg

6839440171_a107fa0ec8.jpg

6839436613_31ac64976d.jpg

6839434901_3db946f224.jpg

This is the oil feed for the turbo- its a t piece off the oil pressure sender.

6839431167_9b83b217bc.jpg

Craig has taken to writing HKS on various parts of my car- ie- the trans cooler bracket.tongue.gif

6839432851_45bb26e17a.jpg

That HKS bracket is now worth huge dollars.thumbsup.gif

It might be worth tracking down some stainless cable ties, http://www.ebay.com.au/itm/20-STAINLESS-STEEL-THERMAL-CABLE-TIES-35-CM-EXTRACTORS-DUMP-PIPE-/220948422796?pt=AU_Car_Parts_Accessories&hash=item33718d608c#ht_500wt_1287 or tie wiring the heat shielding around the cables running near the exhaust housing and under the wastegate pipework. Once you get on the dyno; I don't think they'll last long.

Even if they don't melt, they'll go brittle and crack off in no time.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...