Jump to content
SAU Community

Recommended Posts

i wanna go for a drive but cant, i did my back and cant move :(

did anyone read this? it doesnt really explain what it is. it sounds like something you would find on ebay.

http://www.heraldsun...2-1226173968082

Brock had some idea, consisted of getting magnets/crystals and attaching them to the engine. These "polarisers" were meant to change the direction of energy and blah blah to make more power.

Something along the lines of that. Google it, i haven't heard about it in a long time.

Wasnt aware they were $3.5k rims :(

Might go with a cheaper alternative like mohomo has on his car

Nah, don't get Mo's wheels, it look like arse.

Get Varrostens, $1k and up.

What is this?

I can't even....

IMG_1017_small.jpg

It's 370Z wheels.

350z wheels?

Actually, read above.

@ScottyDoesntKnow

"An Energy Polarizer transmits a high energy mainly generated by the vehicle to which it is attached.

This high energy field - A.B.A. Energy - causes all molecules in it's sphere of influence to be aligned or polarized to the direction of the high energy transmission, and are held in a linked or aligned state.

These molecules are subject to a vibratory rate dictated by the Polarizer.

The printed circuitry in a Polarizer causes a multiplicity of frequencies to be transmitted, affecting each molecule and allowing that molecules and it's environment to absorb specific vibration levels including noises, vibrations resonance and impact harshness which are always present in any vehicle and also to dampen out the effects of imperfect manufacture of vehicle components.

The overall effect on a motor car is to absorb road shocks more completely and quietly, to reduce overall vehicle noises - both inside and outside - to achieve greater efficiency of the power train and steering systems, improving the engine and suspension performance and to create a more pleasant environment for the driver and passenger.

Certain frequencies have not been "tuned out" as they are necessary for increased road safety.

The energy transmitted from the "Energy Polarizer" always flows to that area most effected. That means a major problem area still remains a problem, and the energy is effectively wasted on that area since the overall vehicle is deprived and consequently is less enhanced. So a correctly manufactured and maintained vehicle will always be superior to one that is not, but all vehicles benefit from the fitment of an Energy Polarizer.

It should be noted a vehicle which normal requires high octane leaded fuel is then able to operate on low octane (92) unleaded fuel, without any ill effects whatsoever, when an Energy Polarizer is fitted.

Tyre pressures must be lowered to maximise the effect of an Energy Polarizer. Recommended tyre pressure:-

Standard and 60 series tyres - 24 P.S.I (165 k.P.a).

45 / 50 / 55 series tyres - 22 P.S.I. (150 k.P.a).

Light trucks and commercial vehicles - 30 P.S.I. (210 k.P.a.)"

@ScottyDoesntKnow

"An Energy Polarizer transmits a high energy mainly generated by the vehicle to which it is attached.

This high energy field - A.B.A. Energy - causes all molecules in it's sphere of influence to be aligned or polarized to the direction of the high energy transmission, and are held in a linked or aligned state.

These molecules are subject to a vibratory rate dictated by the Polarizer.

The printed circuitry in a Polarizer causes a multiplicity of frequencies to be transmitted, affecting each molecule and allowing that molecules and it's environment to absorb specific vibration levels including noises, vibrations resonance and impact harshness which are always present in any vehicle and also to dampen out the effects of imperfect manufacture of vehicle components.

The overall effect on a motor car is to absorb road shocks more completely and quietly, to reduce overall vehicle noises - both inside and outside - to achieve greater efficiency of the power train and steering systems, improving the engine and suspension performance and to create a more pleasant environment for the driver and passenger.

Certain frequencies have not been "tuned out" as they are necessary for increased road safety.

The energy transmitted from the "Energy Polarizer" always flows to that area most effected. That means a major problem area still remains a problem, and the energy is effectively wasted on that area since the overall vehicle is deprived and consequently is less enhanced. So a correctly manufactured and maintained vehicle will always be superior to one that is not, but all vehicles benefit from the fitment of an Energy Polarizer.

It should be noted a vehicle which normal requires high octane leaded fuel is then able to operate on low octane (92) unleaded fuel, without any ill effects whatsoever, when an Energy Polarizer is fitted.

Tyre pressures must be lowered to maximise the effect of an Energy Polarizer. Recommended tyre pressure:-

Standard and 60 series tyres - 24 P.S.I (165 k.P.a).

45 / 50 / 55 series tyres - 22 P.S.I. (150 k.P.a).

Light trucks and commercial vehicles - 30 P.S.I. (210 k.P.a.)"

thanks for that. well it looks like holden are going to be putting them in there cars i wonder if they will work?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
    • Wouldn’t touch par if they gave it to me. You need to ask how much power you’re looking to make and then add about 50% to it because that’s what you’ll end up making  The factory box says no more at about 350kw or so, the upgraded synchro boxes won’t handle much over 500kw for long and at that point you’re looking at an auto or dog engagement manual,  once you’ve gone dog engagement you may as well go sequential, they cost a little bit more but it’s worth it  also while you’re at it you should upgrade the transfer case with 10 friction plates 
×
×
  • Create New...