Jump to content
SAU Community

Recommended Posts

Have heard people just whack an eBay manifold on the Ford 4L and a GT35 and run low boost no problems

Would be pretty funny to try with an old piece of shit

Hmmmmmm intradesting I have my grandfathers old el sitting in our paddock :P

they do motorbike and misc. machinery... its all about getting parts really.

after speaking to our mutual friend yesterday, i dont think he's too keen on cashy's at the moment. the workshop will take em though.

after seeing the motor yesterday, needs a replacement crank :angry: (good thing i didnt go stroker kit)

dude... it took you 2 years to change a set of rims

that's cos it's my own car. Plus all monies went to buying apartment instead of unnecessary mods.

Well he builds all sorts of engines

He probably rebuilds an engine a day, not just high performance, lots of insurance ones. So i'd say he's dealt with a wide variety

so does he need engine out or does he engine out, rebuild and reinsert? The less car I need to work with the better. How does this work, do you have to put in an intro or do I just call him and be all like "Tony said deal with it"

Correct

Cash job just means you get paid for the service in cash. Amiright?

But is it tax deductable?

On a side note, I do have an accountant friend with a few years exp that might be interested. He just got married and is on honeymoon atm though...

that's cos it's my own car. Plus all monies went to buying apartment instead of unnecessary mods.

unnecessary mods like fucking what? a pair of cashmere wheel changing gloves?

  • Like 1

that's cos it's my own car. Plus all monies went to buying apartment instead of unnecessary mods.

so does he need engine out or does he engine out, rebuild and reinsert? The less car I need to work with the better. How does this work, do you have to put in an intro or do I just call him and be all like "Tony said deal with it"

He can do it all *if* he isn't busy

Best to just shoot him a PM, just say your from SAU and Tony told you to contact him through it

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
×
×
  • Create New...