Jump to content
SAU Community

Recommended Posts

I like these:

http://www.importmonster.com.au/shop/product_info.php?cPath=40_45&products_id=1899

What's the price look like for you guys, what would you pay..?

Also.. Is it possible to shave a couple of mm off a wheel to make it a few mm higher in offset?.. Sounds dodgey but dem rears will poke out hard and I want to run big tyres.

Edited by UNR33L

Dude with a gun & no will to live has no relevance to a billionaires life

But sometimes a lot of relevance to his death

http://www.dailyfinance.com/2010/06/22/bad-fortune-five-bizarre-billionaire-murders/

I like these:

http://www.importmonster.com.au/shop/product_info.php?cPath=40_45&products_id=1899

What's the price look like for you guys, what would you pay..?

Also.. Is it possible to shave a couple of mm off a wheel to make it a few mm higher in offset?.. Sounds dodgey but dem rears will poke out hard and I want to run big tyres.

Hamish will tell you to harden the fk up, particularly as they are professors

i was considering shaving off offset... bad idea. you're not shaving off offset, you're removing meat that sits on the hub/wheel studs.

just roll guards/sort out suspension, fit tyres that fit etc. you'll be fine

I like these:

http://www.importmonster.com.au/shop/product_info.php?cPath=40_45&products_id=1899

What's the price look like for you guys, what would you pay..?

Also.. Is it possible to shave a couple of mm off a wheel to make it a few mm higher in offset?.. Sounds dodgey but dem rears will poke out hard and I want to run big tyres.

Harden the fk up

Especially as they are professors

D1Rs come in all sizes and offsets

Yeah but only one magnitude of gay

Lee even like 2-4mm would f**k it you think?

Birds d1rs in 20s look sheit!

Lol

Sif 2-4mm will make a difference fgt

That will get you 1 tyre size up which you will never notice.

4mm would be acheived with a guard roller and about 2.3 seconds

Lol.

Aaron has already rolled them for me, maybe I'll go down to import monster one day and try them on..

You had professors? thought you were rocking varrstoens

I want to at least fit some 265s f**k those 225s and 235s what am I gonna do with those lol

Edited by UNR33L

Engine build complete after many dramas.

'greg can you come here and tune the start'

Rock up with laptop

Play with ECU

car starts... and appears to run/idle fine/way smoother than it did before it died, no smoke, no leaks, just... purring away

f**k, expect 7 years of bad luck now everyone

I'm sorry

D1Rs birds?

11025186_690767431046669_180923112286857

That actually looks pretty tough.

People may diss them, but they are lightweight, cheap and can take a beating. Break or rash one and $250 to replace.

Lol.

Aaron has already rolled them for me, maybe I'll go down to import monster one day and try them on..

You had professors? thought you were rocking varrstoens

I want to at least fit some 265s f**k those 225s and 235s what am I gonna do with those lol

You want to shave 2-4mm

Thats going to be the difference between a 255 and a 265.

Or a 235 and a 245

Etc etc etc

What on earth makes you think shaving 2-4mm will allow an extra 20mm?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Also seen this as an option 
    • I get you, we’ll see I’m aiming for 200ish kw now and hopefully 300rwkw down the line after some upgrades maybe like headstuds, E85 flex fuel etc  so trying to make it final for that now, I can get a GTT airbox for $280 so it’s not too bad but not sure if there’s better ways to spend that money. I seen online they say pod filter which isn’t enclosed isn’t good especially for a plus T.      hard to say what to do
    • Meh. How much power can you make from a +T anyway? I wouldn't have though it would be enough to challenge the airbox. It's not as if it's tiny compared with the turbo one. As to putting a pod in a stock airbox .... it's not the filter element that would be restrictive. It would be the air inlet to the box that would be the narrow point, which you could open up regardless of what element was inside. On my R32 I opened up the sort of triangular opening in the bottom front corner of the box, deformed (heated, moulded) some 4" stormwater pipe to fit to that opening and punched a 4" hole down through the inner guard to the spot where the stock intercooler used to be. This was purely in the search for a cold intake, but you could do something similar if you need to open up the inlet side of it. The AFM tube size is the same for both NA and turbo, so the outlet from the airbox is same same anyway. If you're going to do the right thing, then an aftermarket ECU won't care about the AFM (ie, you can get rid of it). But even if it was still there, people pull >300rwkW through them all day, and I suspect you won't be going there.
    • R34 RB25de Neo by the way ^ 
    • Doing a +T on my car and I’ve read the precious forums lots of mixed reviews from sometime back.  checking if anyone has any ideas for airbox or enclosed pod filter or solutions?  I was thinking stock GTT box but some say it’s restrictive? I seen some people try fit in a pod in the box anyone done that recently?  not any good enclosed options ? Thanks 
×
×
  • Create New...