Jump to content
SAU Community

Recommended Posts

that be June:

http://www.sau.com.au/forums/topic/452502-2015-motorsport-championship/

hoping to have a GTR ready?

Or finally find out how slow the GTS-t is on a track .....

Them's fighting words!

Maybe you're right though, with those heavy cast D1Rs and all

that be June:

http://www.sau.com.au/forums/topic/452502-2015-motorsport-championship/

hoping to have a GTR ready?

Or finally find out how slow the GTS-t is on a track .....

GTS-T will hit the track before the GTR does

And if it's slow it'll be the driver, thing is reasonably well set up for a daily

would like to come to sandown, but got shit on :(

gloria off to Centreline Suspension for JDM treatment. i was surprised chris knew what was going on before i had even said anything "so we're going to need a lot of negative camber, and you dont mind if it exceeds 100mm ride height?"

GTS-T will hit the track before the GTR does

And if it's slow it'll be the driver, thing is reasonably well set up for a daily

take a lot to get a gts-t around a track quick,and if it a good daily then it's not there...just ask Simon.

dialing out the understeer of such a heavy motor at speed is very hard.

It's a manageable daily. There are much more friendly cars going about on the street, but people are surprised when they drive it how palatable it is for the power output and how quick it can be putted around mountain roads. I modified it with the intention to make it capable and retain some creature comfort - expensive process and ultimately a compromise for the street is usually a compromise at the track, yes, but even things like 0 camber for a street setup, tyre and brake pad choice...things I can easily change before a track day...make it a better daily driver.

Adjustable everywhere and poly bushes throughout, the KAAZ 1.5 way is wonderfully predictable and helps her to be tail happy when you want it to be, really helps with turn in at moderate to higher speeds and the opposite at lower. Granted I'm not doing 160km/h corners on the street, but it'll be interesting to see how the car goes nonetheless. I think the suspension would be the thing to hold it back given the struts sound a bit shot after years of Toorak Rd. If nothing else I still have a decent whack of power to make use of our long straights. Could always give a better driver a chance in it and see what they think.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...