Jump to content
SAU Community

Recommended Posts

Refinancing a 400k loan up to 80% LVR (without incurring LMI)

400k * 80% = 320k

320 - 250k = $70k equity available (not $150k)

Interest only 5yrs repayment: $1,174/month @ 4.4%

$300/wk rental income = $15,600 income ($1,200/month)

Property near positive geared - excluding rates, body corp, maint, fees etc

800k house @ LVR of 90% if willing to pay LMI around $700k loan (estimate stamp duty applied as well)

$70k equity + $30-40k cash savings will fill the shortfall between Loan vs. House purchase

$700k loan @ 4.4% P&I = $3,500/month repayment

$150k incl Super income is around $8000/month income (after tax)

Bank usually says Single person living expense is around $1100/month (not sure what a couples monthly spend would be - lets say $2k)

$8000 - $2000 - $3500 = $2500/month left over

Don't see any issues with their borrowing vs. income. Could have missed some points, speak to your local mortgage broker on a more realistic assessment on your borrowing.

Pretty close...

We don't lend on the ability to make repayments at current rates lol

No one wants GFC 2

Pretty close...

We don't lend on the ability to make repayments at current rates lol

No one wants GFC 2

No one wants rape either but girls still dress provocatively

That's right I went there

true; the scenario still has a $2.5k monthly buffer so should be safe enough to lend.

You'd be surprised how quickly a surplus like they disappears when we assess lending, especially consumer mortgages where we are heavily regulated.

I doubt 2k living expenses I mean you'd likely have two car repayments two rates, insurance, bills etc seems low to me

HEM/HPI figures (which is what he was referencing) do not include other debts. They are over and above.

  • Like 1

Just get delivery? It's only $7. No store will have click and collect cause hardly any will have their allotment yet.

Sold out now...they must be bleeding them to the online store. Will prolly be available again soon.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...