Jump to content
SAU Community

Recommended Posts

How much does it drop egts on your setup?

They don't drop noticably at all with the new nozzle sizes. I still see 800-810 degrees if I hold it flat past 7000 rpm. This I suspect is due to the reduced volume compared to my last setup. There is perhaps 1-2 degrees more of advance in the ignition map with this setup, which is a nice safety buffer if I want to give it a hard time in 40 degree heat.

Yeah fair enough :)

I think I'll stay away from pre turbo on my car for now

I'd be to worried about water pooling as it would have to make a hard 90deg turn

Might have to try and get a temp reading though as the intake pipe sits directly above the turbos if it is hot enough to keep the water vaporized it may work

I understand the thermodynamics of what your trying to say but it doesn't make sense in reality. If water increased the dynamic comp then why don't you add it all the time? Surely you will gain hp everywhere? I'm not bagging water injection as a way of quenching chamber temps and slowing flame propagation rates but all the hype about it disassociating the hydrogen and oxygen and the water turns to steam which creates greater dynamic comp is a load of.

alot of high powered NA cars do run water meth for a hell of alot more time that you guys do on boost,

however I don't believe he said that it splits the water into Hydrogen and oxygen and it wont as you require a few other factors going on, like electrolysis.

Yet as for the increase in comp, it depends on where abouts in the cycle your talking, on the actual compression stroke you would prob see a decrease in compression as the water absorbs a hell of a lot of heat and cools the mixture making a lower pressure area, however then when you are on the combustion stroke, the water is heated way beyond the point it will remain as water and will become steam and at this stage you will have an increase in compression, im not 100% sure on if the net result will be an increase or decrease in compression overall and i really cant be arsed trying to work it out.

I understand the thermodynamics of what your trying to say but it doesn't make sense in reality. If water increased the dynamic comp then why don't you add it all the time? Surely you will gain hp everywhere? I'm not bagging water injection as a way of quenching chamber temps and slowing flame propagation rates but all the hype about it disassociating the hydrogen and oxygen and the water turns to steam which creates greater dynamic comp is a load of.

Water injected as a vapor is still an uncompressable liquid. This alone is the primary reason dynamic compression increases.

What happens with cylinder pressures when the water turns to steam during combustion doesn't relate to dynamic compression. H2o can not dissociate into base elements from pressure alone either. In the combustion chamber it just expands a lot due to the 950+ degree combustion temps.

Yes water increased all the time would increase power in theory. The problem is metering it correctly so you inject the correct amount per cylinder for ligher loads. If you consider that 425cc/min is correct for a 700hp 3lt 6 cylinder, the correct single nozzle size for the same engine making 45hp is 36cc, or 6cc cylinder. So you see for light loads the issue is getting accurate delivery to each cylinder without the nozzles blocking.

An alternative solution that I have read about for lean burn/economy tuning which might partially solves this issue is steam injection. Injecting as steam allows nozzle sizes to be larger. It also allows distribution to cylinders to be more easily achieved from a common injection point. Steam injection temps are high (say 150+ degrees), but still much less than combustion temps. Steam temps would also drop as they approach the engines intake valve and at the same time raise both the dynamic compression ratio and the effective octane rating of the fuel. This is a completely different concept to performance tuning with WMI though.

I remember seeing photos of a bloke with a supercharged 6 cyl falcon who mounted the nozzle in the snout of the blower and after 6 months had cut a slot in the impeller about 10mm long on each blade

This was back in the 90s so the kits were quite basic and just injected a jet of water rather than a mist

has anyone run pre-turbo for extended use ( eg couple of years) and noted any wear on comp wheel?

There is some good info on the aquamist forum about longevity of pre-turbo systems and wear on the impeller. Long story short was if you inject it correctly as a fine mist and have a good shutoff system there isn't an issue.

Water injected as a vapor is still an uncompressable liquid. This alone is the primary reason dynamic compression increases.

What happens with cylinder pressures when the water turns to steam during combustion doesn't relate to dynamic compression. H2o can not dissociate into base elements from pressure alone either. In the combustion chamber it just expands a lot due to the 950+ degree combustion temps.

Yes water increased all the time would increase power in theory. The problem is metering it correctly so you inject the correct amount per cylinder for ligher loads. If you consider that 425cc/min is correct for a 700hp 3lt 6 cylinder, the correct single nozzle size for the same engine making 45hp is 36cc, or 6cc cylinder. So you see for light loads the issue is getting accurate delivery to each cylinder without the nozzles blocking.

An alternative solution that I have read about for lean burn/economy tuning which might partially solves this issue is steam injection. Injecting as steam allows nozzle sizes to be larger. It also allows distribution to cylinders to be more easily achieved from a common injection point. Steam injection temps are high (say 150+ degrees), but still much less than combustion temps. Steam temps would also drop as they approach the engines intake valve and at the same time raise both the dynamic compression ratio and the effective octane rating of the fuel. This is a completely different concept to performance tuning with WMI though.

Your not listening - if you inject water in the most precise manner you will still lose hp power due to the effect that water has on lowing the flame progegation speed. And as for lean burn engines, slowing the flame front and adding another non combustable vapor is the exact opposite to what you want. I've worked with combustion engineers that have had petrol engine running as lean as lambda 2 and I've never heard of water or steam injection as a theory to help lean burn conditions. Do you realize that chamber temps decrease either side of stoic.

I have a direct injection VQ25 here with the high pressure mechanical fuel pump. I was going to ditch the heads and put the turbo ones on but you just gave me the idea of utilizing the injectors and pump for water injection. If I could get them to fire at different points in the combustion cycle it could have huge benefits, especially with high compression + ethanol...

Your not listening - if you inject water in the most precise manner you will still lose hp power due to the effect that water has on lowing the flame progegation speed. And as for lean burn engines, slowing the flame front and adding another non combustable vapor is the exact opposite to what you want. I've worked with combustion engineers that have had petrol engine running as lean as lambda 2 and I've never heard of water or steam injection as a theory to help lean burn conditions. Do you realize that chamber temps decrease either side of stoic.

Decreasing the flame speed is exactly what you want to do to reduce potential of detonation in high boosted engines, especially if guys are running these engines with tight quench and higher compression.

I spend a few hrs on the stagea today and mounted tank, and ran the lines under the car in convoluted tubing,(did a few other things at same time like running 8ga wire for hardwiring fuel pump)

still have to mount the solenoid/ wire it to igntion and drill and tap the intake pipe for the

injector and its done, maybe next weekend. I was thinking about running a 100cc jet with the stock turbo and see how much more i could get out of it with a bit of timing added for shit and giggles, whats a good

auto Rb25 neo make usually on 12psi-180-190rwkw?

cheers

darren

I have a direct injection VQ25 here with the high pressure mechanical fuel pump. I was going to ditch the heads and put the turbo ones on but you just gave me the idea of utilizing the injectors and pump for water injection. If I could get them to fire at different points in the combustion cycle it could have huge benefits, especially with high compression + ethanol...

Sorry mate fuel injecters wilcorrode/rust up,read it on other forums n was talking with a relative over easter bout this, he water injection on an old carby fed holden statesman. had a very basic setup think he had 5 smallish injectors into the carby into a spacer he had up had no injection at idle, then two would open up with the first two barrels when they opened, then the next 2 with the, 3rd an fourth barrells using the vacum (somehow) then the fith was on the front of the carby an opened under full throttle when there was no vacum powered buy a washer bottle pump. he never changed the timing didnt notice much performance but got a 50% improvement in fuel, went from getting 400km a tank to 600km a tank. but after a couple of months the nozzels corroded/rusted up. an he couldnt find any to handle water (that was quiet a few years ago)

also back in the 80's dad's cousin had water/meth injection on his car had great performance gains but if the car sat for a few weeks or a month the water/meth mix all went to jelly an clogged all the lines an the tank also had to be cleaned out..anyone had these problems?? maybe meth has improved over the years or the were running a different mix ratio.

as for getting power from water an old man from i think Dalby (se qld) did time for not paying tax on water used for fuel, tho thinking he may have bn using electrolisis, he could drive an old bus from dalby to cairns on 40L of fuel..about 2000km!!...tight arse government lol

wish i'd descovered how good water/meth injection a cpl months ago before i spent money on cams to get more power while sacrificing drivability...but its got a nice idle lol

Sorry mate fuel injecters wilcorrode/rust up,read it on other forums n was talking with a relative over easter bout this, he water injection on an old carby fed holden statesman. had a very basic setup think he had 5 smallish injectors into the carby into a spacer he had up had no injection at idle, then two would open up with the first two barrels when they opened, then the next 2 with the, 3rd an fourth barrells using the vacum (somehow) then the fith was on the front of the carby an opened under full throttle when there was no vacum powered buy a washer bottle pump. he never changed the timing didnt notice much performance but got a 50% improvement in fuel, went from getting 400km a tank to 600km a tank. but after a couple of months the nozzels corroded/rusted up. an he couldnt find any to handle water (that was quiet a few years ago)

I knew the pump and injectors wouldn't last long with water alone, I was contemplating flushing the system with WD40 or mixing a little water soluble oil in perhaps. I'm just interested to see what effect direct injecting the water at different points in the cycle would have.

im seriously considering a WMI kit as safety measure and hopefuly bring turbos on sooer,

how would the SNOW stage 2 performance water methanol kit go in an R32 GTR?

is there another kit more suited to these cars?

this may be a stupid question, but where do you purchase methanol from?

Would still be worth it as a safety measure. Even injecting just distilled water

Just curious as to where one would mount the nozzle on a gtr? On the plenum? Or on the intercooler hard pipe joining to the plenum (that's if you have an alloy pipe there and not the stock rubber one)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...