Jump to content
SAU Community

Recommended Posts

My tuner said i need to get a aftermarket fuel reg.

He forgot to mention if i should get a rising rate or a fixed one.

(malpassi,turbosmart or other)

The car is a r33 gtst.

mods so far

fmic

haltech ecu

turbo back exhaust

bosch fuel pump

splitfire coilpacks

greddy ebc

hyflowed turbo

any thoughts would be great with this one.

thanks

Link to comment
https://www.sau.com.au/forums/topic/398778-fuel-reg/
Share on other sites

Do it properly and buy a set of injectors and use the factory regulator (its fine for over 350rwkw).

Obviously depends on the hi-flow as to how viable a FPR is (without injectors).

1. If it'll only make 220rwkw then ok fair enough

2. If the hi-flow will make 250rwkw+, then dont waste time and get a set of injectors

Link to comment
https://www.sau.com.au/forums/topic/398778-fuel-reg/#findComment-6333497
Share on other sites

As above, and generally all are rising rate? (ie with a 1:1 as the manifold pressure rises so does the fuel pressure)

yes, it absolutely needs to be rising rate in a turbo car - the rising means that fuel pressure rises as your boost does.

Um, point of order here. Rising rate regs actually increase the fuel pressure faster than the increase in signal (manifold) pressure. ie, the slope is greater than 1. Rising rate is actually a poor description for them, but that's just how it is. Most things like that are poorly named in the car world where they wouldn't be in the engineering world.

Normal fuel regs are "constant rate".....if you were to use the same poor terminology. But what they really keep constant is the delta P across the injectors.

Link to comment
https://www.sau.com.au/forums/topic/398778-fuel-reg/#findComment-6334940
Share on other sites

there is nothing wrong with changing the FPR, way go to the expense of injectors if a FPR will "fix it" if it doesn't need them, ie if it is getting to 99% duty cycle and the op isn't going higher with power then way not just do the FPR and give himself some headroom and save some coins, other then "it's not the right way to do it" cause the higher ressure will also help atomisation

Link to comment
https://www.sau.com.au/forums/topic/398778-fuel-reg/#findComment-6335099
Share on other sites

If you just need to sneak in a few extra psi to get you accross the line, then just get a nismo fpr that bolts onto your stock rail.... simple and neat.

If your trying to screw 50psi base pressure into it, then get injectors. Nismo, sard etc.

If you just wan't a shiny new toy for your engine bay... buy a well known brand name and make shure it's genuine.

Cheers

Justin

Link to comment
https://www.sau.com.au/forums/topic/398778-fuel-reg/#findComment-6335103
Share on other sites

Do you plan on going much further with the power upgrade?

If you plan on going much further, grab some larger injectors. I have run 550s within standard FPR - but consider that most

After market injectors are rated based on a 3kg base fuel pressure, the factory FPR is rated at 2.55 kg

So 'best' option would be to get some larger injectors and a FPR - as mentioned earlier, Nismo bolt on type is a good option, minimal stuffing around and work well with the factory fuel rail.

For a budget upgrade to give a little extra injector headroom - a FPR by itself can do the job well - once again, Nismo type is neat, easy to fit and works well.

Not a fan of rising rate FPR, as you end up with higher pressure than the injectors are rated at

My 0.02c

Link to comment
https://www.sau.com.au/forums/topic/398778-fuel-reg/#findComment-6335164
Share on other sites

  • 8 months later...

well that's the thing. any standard (or tuned) ECU is based on a specific base pressure. If you put an adjustable FPR on and are not retuning, you need to set it to the same base pressure as the previous FPR, ie there is no point.

The only real use to an adjustable FPR is to get maybe 10-20% more flow out of injectors without swapping them for something larger. In that case you must retune the car anyway, so set it to the standard base + whatever % you need and tune it from there.

Link to comment
https://www.sau.com.au/forums/topic/398778-fuel-reg/#findComment-6730604
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...