Jump to content
SAU Community

Using Two Oil Sandwich Plates?

JustinP

By JustinP,
in Engines & Forced Induction

 Share

Recommended Posts

JustinP Mentor

JustinP

Posted
Posted

Has anyone used two oil sandwich plates before (on top of the stock oil warmer / cooler) and has it caused any clearance issues with the fitment of the oil filter? My skyline is in a million pieces (engine out) at the moment so I can't have a look and estimate the clearance.

I know it's not ideal using two as its just another point of failure / leaks, but it will make my life easier :P

Cheers

Justin

Link to comment
https://www.sau.com.au/forums/topic/402155-using-two-oil-sandwich-plates/
Share on other sites
JustinP Mentor

JustinP

Posted
  • Author
Posted

No I mean two sandwich plates in addition to the stock oil warmer / cooler. I have an oil cooler to install with a built in thermostat in the sandwich plate, so it doesn't have room for the 1/8" NPT sensor holes. I need to install an oil pressure sensor and will possibly install another oil temp sensor down the track so i will need a second sandwich plate with the sensor holes.

I realise I could get rid of the factory oil pressure sensor and install the new one there, but then I would need to find a BPT to NPT adapter to fit it, and the (crap) factory oil pressure gauge would stop working, which whilst pretty much useless would annoy me to not have it working. I think you can get a BPT adapter with a tap for both a BPT and NPT sensor, but I havent been able to find one anywhere.

JustinP Mentor

JustinP

Posted
  • Author
Posted

Ok, most common thing to do is get a relocator kit. Then the oil filter relo plate has the bungs u require

That is the third and probably smartest option :) - but if I did want to do go with the 2 sandwich plates do you think I would have a clearance issue between the oil filter and the drivers side wheel arch? As my engine in not in the car I cant visualise it.

I am just looking the oil filter now and I do use the smaller R34 type ones, so I am pretty sure there will be plenty of room.

JustinP Mentor

JustinP

Posted
  • Author
Posted

Can't you just drill and tap some holes in the thermo sandwich plate?

I thought of that but there is only a small area where that might be possible, and its kinda recessed and on an angle:

http://www.racerpartswholesale.com/product/1597/Mocal_Sandwich_Plate

Not sure it how well it would work.

roba Enthusiast

roba

Posted
Posted

I use two on my boat.

one for oil supply from dry sump + sensors

one mocal sandwich plate for thermostat - attached to heat exchanger

No dramas in terms of "its just another point of failure / leaks"

Not sure on clearance issues tho...

post-29626-0-81291700-1339281354_thumb.jpg

JustinP Mentor

JustinP

Posted
  • Author
Posted

I use two on my boat.

one for oil supply from dry sump + sensors

one mocal sandwich plate for thermostat - attached to heat exchanger

No dramas in terms of "its just another point of failure / leaks"

Not sure on clearance issues tho...

Using an RB25 in a boat = awesome! :P

I'm going to order one of the Just Jap items linked to above, I think clearance will be fine.

Thanks everybody.

  • 3 years later...
V28VX37 Veteran

V28VX37

Posted
Posted

Hi all, I've just ordered a Driftworks oil cooler kit with the Mocal thermostatic sandwich plate, which doesn't have sensor points.

I have an existing sandwich plate for Defi sensors and I'm wondering if I can run both at the same time? The car is an R34 GTT with the Neo engine and standard small Ryco Z422 filter.

The other option is to add an extender piece (?) between the oil cooler sandwich plate and the braided line where you can hook the sensors but I'm not sure if such a part exists?

Kinks Grand Master

Kinks

Posted
Posted

1/8 npt into 1/8 bpt won't seal?

NOPE

the threads are incompatible, but they are close enough that you can force it in. however that means you have over stressed some of the threads and it could develop a leak at any time. Which is probably a bad idea if you use it where you care about the quality of the seal, for example.. in a pressurised oil feed!

to answer the original question, in a GTT I don't see how clearance could be an issue. I reckon you could stack 5 or 6 sandwich plates before you have any issues.. there's a ton of room!

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      NC MX5

      By Dose Pipe Sutututu · Posted

      Lamb roast on Saturday will be different 🥲
    • TurboTapin
      RB25DET with solid lifters - which cams ?

      By TurboTapin · Posted

      They are under bucket shims. Tomei provides a test shim kit and then any measurement of shim required. 
    • GTSBoy
      RB25DET with solid lifters - which cams ?

      By GTSBoy · Posted

      I always wondered how you were supposed to buy a set of 24 buckets and somehow magically have every single one of them yield exactly the desired clearance. I would have thought you'd need to assemble a cam with either 12 "sample" or "example" buckets of known top thickness (or a single such sample/example 12 times over!!) measure clearances at every valve, and then do the usual math to work out what the actual "shimness" of each bucket needed to be, before buying the required buckets to make up he thicknesses that you didn't have on hand.
    • TurboTapin
      RB25DET with solid lifters - which cams ?

      By TurboTapin · Posted

      I now seem to be limited in power due to my rev limit/hydraulic lifters in my built RB25. I'm looking into converting over to Tomei solid lifters. Question for anyone that has done the conversion. I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  I don't know where I got this idea, as so far I see no mention of this in any of the Tomei documentation. It just states I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      I couldn't agree more. I should have started from the get-go with a NEO or solid bucket conversion. I started looking into converting over to solid lifters yesterday. Now for some reason I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  But I see no mention of this on any of the Tomei documentation. It just states that I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
×
×
  • Create New...