Jump to content
SAU Community

Recommended Posts

Hi Guys,

Im wanting to build a reliable 500hp Rb25 and im wanting to know how and what parts would achieve this.

Its going to be my daily along with a few track days. What parts do you guys recomment that will make/handle this power?

Link to comment
https://www.sau.com.au/forums/topic/413751-how-to-build-500hp-rb25/
Share on other sites

I think what they're trying to say is, there's already plenty of info on here. Do you mean 500 crank HP or 500 rear wheel HP? Would you be happy with 470 crank HP or 300rwkw?

Best resource: http://www.skylinesaustralia.com/forums/topic/55845-rb25-turbo-upgrade-all-dyno-results/

44 pages of RB25 goodness, from 150rwkw to 700rwkw.....

And if you search "500 HP RB25" it's the 6th result.......

For me, I think a reliable 500whp (but not much over) RB is as follows:

Upgrade valve springs and retainers

Appropriate cams

Forged pistons

Entry level H beam rods

Larger capacity sump

Oil pump drive collar

Quality oil pump

Oil restrictors to head (see KiwiRS4T sig for a collar and restrictor deal)

Head studs

With that stuff there and a 35R sized turbo you will have a good reliable engine that will do your 500whp everyday and wont end up letting you down.

You can skip the internal work and replace the motor when/if it dies possibly every year or two. This is a guestimate.

Please note the general consensus is that 20k is not enough to turn a stock skyline into a 500whp machine and 30k is more likely.

fuark that's sexy.. I like how the turbo is mounted, allows for the power steering reservoir to remain where it is... the dump probably presses on the A/C drip aye?

  • 3 years later...
  • 1 month later...
On 26/10/2016 at 5:06 PM, CaptBaker said:

is there a parts list/ some sort of "build thread" for this?

T67-25g Greddy turbo kit.

850cc BLITZ injectors

Greddy intake plenum ( tested stock vs the current q45 throttle and found no diff in power)

115mm greddy R-spec intercooler

Greddy race radiator

Greddy Header tank

Trust Titanium exhaust

GREDDY heat range 9 pro plugs (use denso IK01-24 now as the greddy are impossibly expensive even in NGK format)

PowerFC (soon to be emtron KV8)

Car also now has TOPSTAGE carbon front diffuser and Rear wing.

 

 

This car will lap winton or phillip island non stop without getting hot or having any IAT issues, we did a 30 lap test session with JT and our VK twin turbo LS1 to check endurance.

 

jt vk 2.jpg

jt vk.jpg

  • Like 1

Hi Mate,

I'm not too far off (430hp at 16psi on 98). I'm aiming for 500hp, I hope the below helps, I will be there soon (fuel system is currently being upgraded).

You probably don't need to do everything I did but at-least you can get a picture on what is needed:

  1. Gt35r turbo
  2. FMIC
  3. GReddy wastegate (60mm...i think)
  4. 6boost manifold
  5. ecu/boost management (I'm using a PFC and profec b)
  6. I had nismo 555cc injectors on stock rail (now have 1000cc's, turbosmart fuel reg and sorting surge tank/pumps)
  7. 260deg 9.25mm lift Tomei type b cams (from memory) with headwork done + springs
  8. forged pistons
  9. forged rods
  10. upgraded coil packs
  11. all the additional engine equipment (harmonic balancers, belts etc etc)
  12. larger sump with head oil drain
  13. I have a 3'' zorst. I've been told this is okay, but I would increase to 3.5"
  14. Plazmaman plenum
  15. clutch
  16. Not to mention blockwork- honing etc
  17. radiator

That's about all I can remember now, that doesn't take into account everything else that you will need. Suspension, brakes etc.

You could always to e85, but for practicality I can't justify it at the moment.

There was a lady on here a few years ago that really helped me out, but she was running a T04Z. Perhaps search rb25 T04Z, her build guide was excellent.

Agree with GTSSCOTT- your looking at about $10-15k to build the engine if you just do the basics.

13668992_10154330564827510_4643053593968356568_n.jpg

Edited by r33cruiser
  • Like 1

You can make that power with less parts and the right parts too.

Best to look into something twin scroll, divided rear housing and ball bearing.. I won't throw turbo models around because it would start a holy war LOL

If you can settle for less power, a low 300kw rb25 is a lot cheaper to build/run reliably than a 400kw one.

You can even skip the whole rebuild the engine drama if you want to (head gasket is probably a good idea along with better valve springs if you are running decent boost), lots of cooling (engine and oil) and stick to e85 or add wmi for safety when going harder on it.

Hi Mate,
I'm not too far off (430hp at 16psi on 98). I'm aiming for 500hp, I hope the below helps, I will be there soon (fuel system is currently being upgraded).
You probably don't need to do everything I did but at-least you can get a picture on what is needed:
  1. Gt35r turbo
  2. FMIC
  3. GReddy wastegate (60mm...i think)
  4. 6boost manifold
  5. ecu/boost management (I'm using a PFC and profec b)
  6. I had nismo 555cc injectors on stock rail (now have 1000cc's, turbosmart fuel reg and sorting surge tank/pumps)
  7. 260deg 9.25mm lift Tomei type b cams (from memory) with headwork done + springs
  8. forged pistons
  9. forged rods
  10. upgraded coil packs
  11. all the additional engine equipment (harmonic balancers, belts etc etc)
  12. larger sump with head oil drain
  13. I have a 3'' zorst. I've been told this is okay, but I would increase to 3.5"
  14. Plazmaman plenum
  15. clutch
  16. Not to mention blockwork- honing etc
  17. radiator
That's about all I can remember now, that doesn't take into account everything else that you will need. Suspension, brakes etc.
You could always to e85, but for practicality I can't justify it at the moment.
There was a lady on here a few years ago that really helped me out, but she was running a T04Z. Perhaps search rb25 T04Z, her build guide was excellent.
Agree with GTSSCOTT- your looking at about $10-15k to build the engine if you just do the basics.
13668992_10154330564827510_4643053593968356568_n.jpg


Really helpful!
Is that 430hp at the engine or wheels ?
Cheers

Yep.

If you are looking to go down the built engine road there will be many costs that you have to take into consideration. Its the small things like:

bearings, electrical work, you might have to replace stock parts like the C.A.S, thermostat, you might need to do some custom fab work etc etc.

Extra costs can quickly add up to $5k in themselves.

We don't mean to scare you off, its a great experience. I stupidly began my build thinking it would be "drive in, drive out"- its not haha

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...