Jump to content
SAU Community

Recommended Posts

Disregard lol

Yes it should be quite responsive Dale, i was considering upgrading to the bigger rear housing but to be honest im over spending money and i just want to drive the thing.. I think the result is going to blow the 2.6 set up out of the water

perfomance should be increased by

2.9 stroker

compression bumped to 9.1 from stock

More responsive cams

Port work with standard sized valves to maintain airspeed

Much better valve springs (ferrea Dual valve springs) old ones were slinkys

Ceramic coated entire exhaust side

Engine is ready for pick up, just waiting on exhaust pick up

haha i could have the engine in by next week... but then it could be at the mod shop for up to a month (large variable) haha

it needs a couple of small repairs done and a run in Tune. The run in tune wont take Yavuz long... Go and drive it for a day straight (Nato runs) , bring it back in for full tune hahah

  • Like 1

Meh what rubbish, throw a bit of boost into it on the dyno with some load.. Tune it

drive it around (not highway ks, you need to load the engine up)... keep the RPm reasonable

we did Pauls car in 2 days from memory *Drives with brakes on hahah

They tell me at CRD to take as long as I can to run it in but drive it normal. Not sure what boost will be on it, not much I guess ?

Did they build the engine? Usually its a safe guard for the tuner if they haven't built assembled it themselves.

The longer you run it in, the longer it lasts generally, but who is really expecting 100 000kms from a built motor.

Joey, after tune I ran the boat in at the drags, seemed to work well, LOL.

From my understanding the motor is run in within the first 20 minutes of running hence why it is so important to get some power into it asap.

Isn't it all just about getting the honing on the bore sorted to get the seal?

Yep that's about right Mark.. I've seen engines that are baby'd just pissing out oil. The. Got put on the dyno for 15 min with some load and boost and the blow by nearly stopped all together.

I believe the contributing factor these days is the precision in piston ring manufacturing.

FMW = Forged Milled Wheel in B-W speak. So billet compressor.

I've found getting a good seal in the bores can take much more than 15mins on the dyno, especially when using chrome rings. A good flogging with plenty of combustion pressures pushing the rings out, and a mineral oil helped mine immensely.

Mine was driven for 2000km - nothing over 5000rpm on highway and NZ open roads (which are not straight). Put it on the dyno gave it boost and absolutely no blow by. All in the engineering job I say.

And I am glad this thread came up I was thinking of upgrading to a single BW turbo (ditching the -5's).

Might be a good idea.

Its thread's/vids like these that get me excited for my build. Btw the car looks great. My understanding was that a 2.9 stroker would make the walls of the block too thin.. is that bs? What width piston are you using?

Edited by Tyranus

Its thread's/vids like these that get me excited for my build. Btw the car looks great. My understanding was that a 2.9 stroker would make the walls of the block too thin.. is that bs? What width piston are you using?

It's a 79.3 mm stroke with 86.5 or 87 mm pistons. Not sure if Joey had to go to the next size.

Its thread's/vids like these that get me excited for my build. Btw the car looks great. My understanding was that a 2.9 stroker would make the walls of the block too thin.. is that bs? What width piston are you using?

Using a custom 87mm piston with a heightened pin location to allow for a longer rod (off the shelf) and better rod/stroke ratio. There was a small worry about having to make clearance at the base of the bore for the extra throw but after a trial assembly it cleared easily

Its a bit under 2.9L atm, but with an 88 mm piston its damn close. I kept to the 87mm cause im trying to make it last as long as possible

an 88 has been done many times before though :)

Mine was driven for 2000km - nothing over 5000rpm on highway and NZ open roads (which are not straight). Put it on the dyno gave it boost and absolutely no blow by. All in the engineering job I say.

And I am glad this thread came up I was thinking of upgrading to a single BW turbo (ditching the -5's).

Might be a good idea.

I have a graph of 2 very similar setups, one with a BW 83/75 and one with -5's

Take a guess who smoked who haha

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
×
×
  • Create New...