Jump to content
SAU Community

Recommended Posts

funny that 9 years is "old" for a modern euro car, they were sure built to last for a planned period and then be replaced by a new one. I'd stay the hell away from anything outside warranty, it would be a quick way to burn money when your $40k second hand car needs to be thrown away.

  • Like 1

@Shoota_77Thanks for the reply, I'd figured as much. I have been keen on one of these for a while but then decided against for the exact reasons @Duncanhas described above. Considering this one has already had $ thrown at it I am seriously looking into it.

3 hours ago, Duncan said:

funny that 9 years is "old" for a modern euro car, they were sure built to last for a planned period and then be replaced by a new one. I'd stay the hell away from anything outside warranty, it would be a quick way to burn money when your $40k second hand car needs to be thrown away.

Yeah fair point :) .  It could be worse.  You could buy a BMW and have a horrid f**king car from day one...

  • Haha 2
  • Sad 1
36 minutes ago, admS15 said:

@Shoota_77Thanks for the reply, I'd figured as much. I have been keen on one of these for a while but then decided against for the exact reasons @Duncanhas described above. Considering this one has already had $ thrown at it I am seriously looking into it.

You will love it as long as you're aware of the downsides!  My second Audi way back in 2010 was a Q5 3.0TDI and I loved that car!  It was fast as hell and yet insanely good fuel consumption at the same time.  The SQ5 version of the 3.0L TDI engine is a whole another level of fun!  We still service heaps of them.  There's one the same vintage as the one you're looking at sitting in the carpark as we speak!

  • Like 1
5 hours ago, admS15 said:

Downsides you say, don't we all own Skylines... Well I have a skyline for backup when the Audi fails 😄

You're fu(#ed then if a Skyline is your reliable back up plan! 🤣🤣

  • Haha 2
On 05/01/2023 at 12:56 PM, Shoota_77 said:

Yeah fair point :) .  It could be worse.  You could buy a BMW and have a horrid f**king car from day one...

Lol funny, I was thinking when reading through this I thought about a couple of mates BMWs when reading the "funny how a 9 year old Euro car is considered old" when I've got mates pushing late 2000s (over 12 years old :/ ) BMWs with stock almost everything harder than we'd typically not even think anything of having to replace a heap of stuff on our Skylines to be able to achieve when they were the same age.   I've got a BMW around that age and it is still farrrrr from a horrid car, best thing I've owned in every way aside from fuel consumption haha.   It's 1.5l/100k worse than my old Honda Jazz in equivalent driving conditions, but otherwise that too.

 

1 hour ago, Lithium said:

BMWs with stock almost everything harder than we'd typically not even think anything of having to replace a heap of stuff on our Skylines to be able to achieve when they were the same age.

 

Can you rephrase this? I've tried to read it a few times and can't understand if BMW is good or bad. Truthfully tho, you can't really know if a car is going to hold up to the abuse of the ages until it actually becomes old in the first place.

  • Haha 1
17 minutes ago, Kinkstaah said:

Can you rephrase this? I've tried to read it a few times and can't understand if BMW is good or bad. Truthfully tho, you can't really know if a car is going to hold up to the abuse of the ages until it actually becomes old in the first place.

Oh wow!  Sorry, a bit sleep deprived today and I had started rewriting some of my original post and got sidetracked and managed to turn it from being hard to read into complete nonsense.   

The intention was to delete everything but the last sentence because I decided I was going too off topic, but seeing as I screwed up...  the two points that paragraph was meant to convey and got garbled:

1) I know people pushing 10+ yo BMWs with mostly stock hardware hard enough to run 130+mph traps without issue

2) When our Skylines were that kind of age we thought nothing of replacing the equivalent kind of stuff to keep them happy, and make them go quicker.  Ignition stuff, oil control, fuel bits, boost leaks. 

All par for course when playing with "special" cars - BMWs just have more sensors and flash more lights than the Skylines did when something isn't working, but helps you know something is up instead of eventually running a bearing, blowing a turbo or generally having a subpar performing setup and tends to not be a biggy if you deal with the things that need to be dealt with properly.  

Anyway, sorry - I had MEANT to make it a far more concise and less off topic post but fumbled it.

Edited by Lithium
  • Like 1
On 05/01/2023 at 10:59 AM, Shoota_77 said:

You will love it as long as you're aware of the downsides!  My second Audi way back in 2010 was a Q5 3.0TDI and I loved that car!  It was fast as hell and yet insanely good fuel consumption at the same time.  The SQ5 version of the 3.0L TDI engine is a whole another level of fun!  We still service heaps of them.  There's one the same vintage as the one you're looking at sitting in the carpark as we speak!

This happened today and is now sitting in my driveway. 

 

8i74cf8zcwnqhypb858348arv.thumb.jpg.85529523dde4c5986efa81c27f1da92e.jpg

 

Drove it home to Melbourne from Canberra. 7 hours to get acquainted. What a wonderful piece of machinery. Smooth AF, just does things without fuss or drama. Averaged 6.9lt/100 for the trip. Not bad for a 2 ton lump.

  • Like 2
9 hours ago, admS15 said:

This happened today and is now sitting in my driveway.

Drove it home to Melbourne from Canberra. 7 hours to get acquainted. What a wonderful piece of machinery. Smooth AF, just does things without fuss or drama. Averaged 6.9lt/100 for the trip. Not bad for a 2 ton lump.

Awesome,  congrats!  Definitely an awesome car and you'll love it!  Wait till you see the disappointed faces of people when you leave them in your dust at the lights.  So fast for a diesel!

  • Like 1
  • 3 months later...

Thought I'd post up some photos of my new sequential gearbox-

received_6094901280624556.thumb.jpeg.00200a42f62459e0b95bca0ca9bfafbf.jpeg

received_260190439684984.thumb.jpeg.f401e2621ba18c526956720d68a60c5e.jpeg

20230416_151316.thumb.jpg.b68bec37005912a041882d4fb8d65999.jpg

20230421_083320.thumb.jpg.afe78f80f8b87d0a1ee3268ce77b920b.jpg

20230421_152752.thumb.jpg.f7f5d73321577231a3f68d1a2dae6d33.jpg

20230429_190140.thumb.jpg.5c916615cad09097cde89012b2fb581f.jpg

 

Yep, the kids won, no Samsonas or PPG for me......  🙁🙁

Decided that waiting 18 months for the pool company to install my pool wasn't happening so did it all myself. Probably the most stressful thing I've done in my life. So much pressure making sure everything was perfect prior to the pool arriving.  Soooo many things to organise on the day of the pool arrival (pool itself, crane to lift it over the house, backfill material delivery, dingo delivery, water truck, guy was there getting rid of the dirt for me.  It was full on.  All ended up pretty good in the end. Not perfect but good enough!

Could have actually bought a whole additional GT-R with what all this has cost me.  Bloody kids better live in the pool for the next 5 years or I'll never forgive them.

Have done nothing on the car because this has consumed my life for the past month. Can't see myself getting back into it until late in the year once I've finished everything on the pool and surrounds. 

 

  • Like 7
6 hours ago, soviet_merlin said:

Holy shit, no half measures there. Nice work! The pool looks big enough you can apply for hosting the next olympics.

Yeah it was a bloody big hole!  Took 2 1/2 days just to get rid of the dirt from it!  I’m 6’8” so that gives you a good idea how deep the hole was.

The pool is 10.5m long and 4.1m at the widest point. Can’t wait for summer to enjoy it!

  • Like 2
  • 3 weeks later...
11 hours ago, r32-25t said:

I can see it now, every time there’s no one in it you’ll be sitting in a dark room and looking out the window at it just filled with rage 

I’ll be sitting in the shed in my non mobile Skyline up on the hoist, peering out the window to my $90K pool completely devoid of laughing children, dreaming of the sequential gearbox that I could have been slamming through the gears on while up the hoist going nowhere….

  • Haha 3
  • 2 months later...

I need to do @Dose Pipe Sutututu and change the title of my build to something to do home renovations....

Operation GT-R pool is nearing completion.  Been a pretty full on month of hard work nearly every weekend.  Learnt a lot of new skills along the way!  Pretty happy with how it's all come along so far.  Just got the pool house put up over the weekend which was a pretty mammoth task.  It's massive overkill for what it is!  I built it with 200mm square steel posts 4m high at the front so it's monstrous!  I had to hire an excavator again to put it all up.  Putting up the front legs and the 8m long horizontal beam across the front was a bit daunting given the proximity to the house and the pool.  I had visions of dropping it and smashing the edge of the pool....

Once I've finished tightening up the frame and painting the uprights I've just got to lay the 100mm PVC stormwater pipe around the pool which will act as my drain.  It will be buried under the concrete and then I'll cut a slit into the concrete immediately above (and into) the PVC pipe which will catch the water and drain it away.  Hope it works...  I saw it on another pool but it was under tiles so they just left a gap between the tiles.  Bit trickier with a full concrete surround but I'll make it work!

 

So once that is all done, I'm REALLY hoping to get back into GT-R mode.  I know I'm ready to get back into it as I've started parts and tool accumulation again...  I had a little play on the car a few weeks ago just further working on the strut towers and smoothing them out.  Trying not to be too anal....

I keep changing my mind every 5 minutes but pretty sure I'm going full white underneath.  I've ordered the tintable Raptor this time so I can tint it matching white.  The final decision will be left till the last minute.  I've got black and tintable so can do whatever takes my fancy on the day that I get to it!

 

I've also ordered 4 metres of 4" titanium exhaust tubing....  Although it's probably going to cost me another couple of grand I'm going to redo my exhaust in full titanium apart from the mufflers/cat which are stainless.  I ordered in some titanium coupons as well to get my eye back in with the TIG.  I'm VERY tempted to get myself a new welder too.  Unimig have a new welder out now that is a proper multi use welder that does MIG and AC/DC TIG.  Still need two gas bottles but the idea of having one machine rather than 2 cluttering up my shed is pretty attractive.  Very confident I'll end up with a new one it's just whether it ends up being 2 new welders or just one.  In reality I do a LOT more MIG than TIG but still want a decent machine for both.  Especially considering the price of titanium, don't want to waste any of it because of a machine that isn't up to the task!

Another new tool I purchased which is AWESOME is the Milwaukee 12V 90 degree die grinder!  Awesome little tool.  Chews through batteries VERY quick but so much easier to use than carting around an air hose everywhere and I can use it anywhere obviously not need an air line or cord.

One of these little suckers-


Milwaukee 12V 6.0ah Li-ion Cordless Brushless Fuel Right Angle Die - Angle - Grinder Combo Kit - M12FDGA-602BA

 

I also bought a cheap Vevor mag (magnetic) drill.  Whilst limited use (apart from all the building I've been doing) it's a bloody weapon!  It was only $325 so cheap really.  I used it to drill a 40mm hole through 20mm thick steel and it absolutely chewed through it in no time!  I'm sure I'll find more uses for it in the future to justify it's purchase!

 

May be an image of hand drill and text

Pool progress pics-

No photo description available.

May be an image of pool

May be an image of cold frame and grass

May be an image of 1 person and trampoline

May be an image of pool

May be an image of pool

 

Enough of my boring waffle.  Hopefully next post is nothing to do with pools and all to do with Skylines!

Good luck with your projects guys!

  • Like 5

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
×
×
  • Create New...