Jump to content
SAU Community

Recommended Posts

im yet to put mine in too just need to get my fuel rail. Which fuel rail did you use to fit it under the plenum.

Anychance you could also tell me if the R34Neo injectors you pulled out were 11mm or 14mm. Seems to be two answers on the threads im reading.

Edited by B-rice

Just used the standard fuel rail and 4mm spacer man. It still clears the plenum easy as, no worries there. Ah to be honest i didn't even measure the size difference between the old ones and the new ones. I just sprayed lanolin on them and they went into the fuel rail fine and didn't move around at all when i put the retaining clips in. With my luck i wouldn't be surprised if i bought the wrong ones haha, anything i do seems to be one step forward and two steps back!

I've got my stock injectors sitting in a box at home, ill measure them for you tomorrow. Pretty sure they are 14mm though.

Sweet, cheers dude.

Also, new turbo finally arrived! It is much bigger than i thought it was going to be hahaha. It is going on tonight and is the last thing i have to get sorted before the car goes down to trent this weekend for tuning! Fingers crossed it bolts up all sweet and i don't have anything bite me in the ass >_<

YKhkPjW.jpg

CcXmkpJ.jpg

hQaV4j1.jpg

KDo6Zxp.jpg

Edited by iruvyouskyrine

Any idea what size studs I need? And how do I get the olds ones out?

Trying to make it fit by clocking the turbo but don't think it will work.

From memory the factory ones are 42mm, so it depends what size spacer you have. I think Stao uses a 15mm spacer, so you will need to get studs at least 15mm longer. I believe I went with 67mm studs.

Standard studs are 39mm, parts that protrude from the manifold is only 24mm, turbo housing is 10mm, spacer is 16mm.

So standard studs are 2mm Fromm even being flush with new turbo.

Will try and get it all sorted tomorrow, hopefully have enough time to get it sorted before this weekend >_<

This is what i would be after yeah? Hopefully can source some locally if not then i'm pretty much farked before this weekend haha.

http://www.sonicperformance.com.au/95015/Stud-_and_-Nut-Kit-GT30_or_GT35_or_GT42_or_GT45-M10x1.5-X-4/pd.php

Edited by iruvyouskyrine

Yep, they are what I used. Be warned, mine warped severely after about 2000kms. I had to cut two of them to get them off.

But MTQ were very surprised and said it shouldn't happen, and because I couldn't find any inconel studs I just used the same ones again. They seem to still be ok.

Got the turbo on finally after fighting with oil and water lines. Found it interesting that the turbo doesn't have a little nipple or similar to run to the wastegate? Just used a spare nipple on my plenum and run it to that.

2UIpC8C.jpg

BUlsUA2.jpg

Run the wastegate as close to the turbo outlet as you can. Stao really should put a nipple on the turbo. But you want the wastegate plumbed into a source as close to the turbo as possible, because of you get a leak somewhere and the boost pressure is lower at the plenum then you could be working the ass off the turbo, superheating the intake charge. If that means getting a nipple put onto the hot side cooler piping then do that.

Would probably be ok for the tune. You should really check for leaks before it goes on the dyno anyway, but hopefully it's ok. But if Trent can't do it, I wouldn't worry too much about it. Just do it at some point.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
×
×
  • Create New...